Mitsumi electronic HD8000 user manual Terminal cover with anti-theft alarm device

Page 38

Terminal cover (with anti-theft alarm device)

This projector includes a terminal cover with Anti-Theft Alarm device. Once the terminal cover is installed, its Anti-Theft Alarm device will detect vibration caused by the projector being moved and emit an alarm.

•Mitsubishi assumes no responsibility or liability for theft or other damages.

Procedure for setting the anti-theft alarm device

Inserting the batteries into the theft warning device

1.Open the battery cover of the theft warning device.

2.Check the (+) and (-) ends of the battery, and insert it from the (-) end first.

Battery cover

ON

Power switch

4.Install the projector in a specified location.

5.Press the battery level check button until you hear a buzzer sound.

6.Remove the safety pin.

The anti-theft alarm device is now in standby.

•This package includes a sticker which shows that the anti-theft alarm device is active. Visible placement of this sticker is recommended.

•To temporarily halt the anti-theft alarm device, insert the safety pin.

•Vibrations will not cause the alarm to sound for several seconds after the power switch is turned ON.

•Vibrations will not cause the alarm to sound for several seconds after the safety pin is removed.

•Vibrations and shocks from earthquakes may cause the alarm to sound. In such situations, insert the safety pin to halt the alarm.

•Batteries may come loose during transportation. Please remove them beforehand.

•Inserting the battery from the (+) end makes it difficult to fit the (-) end into the coil spring. Forcing in the battery in such a position may shred the outside label, causing a short circuit and overheating.

•See page 6 for information on how to handle batteries.

3.Close the battery cover.

Safety pin hole

Safety pin

Screws

4.Insert the included safety pin into the safety pin hole.

•If the safety pin is not inserted, the vibrations and shocks of normal use may cause the alarm to sound.

5.Turn the power switch ON.

Installing the terminal cover

1.Insert the four tabs on the terminal cover into the holes on the projector’s side.

2.Slide the terminal cover toward the back of the projector.

Tabs

3. Tighten the three screws that keep the terminal cover in place.

EN-38

Procedure for changing batteries

How to check battery level

Use a pointed object to push the battery level check button.

Battery level check button

•A buzzer will sound while the button is being pushed. If there is no buzzer sound, then batteries need to be changed.

•Sounding the buzzer for a long time will consume battery power.

Changing the batteries

1.Insert the safety pin into the safety pin hole.

2.Loosen the three screws that keep the terminal cover in place.

3.Slide the terminal cover toward the front of the projector.

4.Pull the terminal cover toward you and remove it.

•Attention must be paid when removing the terminal cover as there could be foreign objects inside.

•Removal of dust found inside the terminal cover is recommended when changing batteries.

5.Open the battery cover and remove the old batteries.

6.Check the (+) and (-) ends of the new battery, and insert it from the (-) end first.

•Use alkaline AA batteries.

•Standard battery life is approx. six months (when using alkaline dry cell batteries). Please check the battery level and change batteries regularly.

7.Close the battery cover.

Page 37 Page 39
Image 38
Page 37 Page 39
Contents HD8000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Do not keep using the damaged projectorPreparing your projector Checking accessoriesInserting the batteries into the remote control Control area Terminal board Preparating your projectorOverview Remote control Bottom sideUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleWhen the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceWhen fine streaks are seen on projected images Setting up your projectorAdjusting the projection angle When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesFor monitor connection Plugging the power cordViewing computer images For audio output connectionProjecting images Remove the lens capTo stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteViewing video images Connecting the projector to video equipmentConnecting to a video player, etc Connection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 How to change the settings With the remote control Volume from the speakerSetting the aspect ratio With the Feature menuSetup Menu operationMenu operation How to set the menusAvailable settings in the menus EN-24 EN-25 EN-26 EN-27 To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerHow to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive filterSet the background color Advanced featuresSetting procedure Set the image sizeTo cancel the password function Advanced featuresPassword function To enable the password functionFreeze To use the split modeSplit To change the input source of the left or right screenOperation Mouse remote controlProjector + computer with USB connector Up buttonPJLink Supervising and controlling by computerProjectorView About PJLinkIndicators Normal conditionProcedure for changing batteries Terminal cover with anti-theft alarm deviceProcedure for setting the anti-theft alarm device Interval of lamp replacement Replacing the lampTo replace the lamp Reset of the lamp operation timeReplacing the lamp Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensCleaning the air-filter Accessory air-filter unitAttaching the accessory air-filter unit For the air-filter whiteTroubleshooting No image appears on the screenImages are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Real mode ConnectorsDimension drawings unit mm Without terminal cover With terminal coverMitsubishi Electric Corporation
Top Page Image Contents