Planar PR3020, PR5020 manual Adjusting the Projector Level, User’s Manual

Page 24

Adjusting the Projector Level

User’s Manual

Adjusting the Projector Level

Take note of the following when setting up the projector:

•The projector table or stand should be level and sturdy.

•Position the projector so that it is perpendicular to the screen.

•Be sure cables are not in the way or can cause the projector to be knocked over.

1.

2.

3.

To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B].

The height adjuster drops down [C].

To lower the level of the projector , press the height-adjuster button and push down on the top of the projector.

To adjust the angle of the picture, turn the tilt adjuster [D] right or left until desired angle has been achieved.

– 16 –

Image 24

Contents Page Planar Systems, Inc Planar Customer SupportCorporate Headquarters 1195 NW Compton Drive Beaverton, OR Telephone US 1-866-PLANAR1 866 Outside US 503User’s Manual CopyrightDisclaimer Trademark RecognitionImportant Safety Information Symbols UsedRemote Control General Safety InformationPower Safety Cleaning the ProjectorSymbol Explanations Replacing the LampMain Features Cables, Replacement Lamps and AccessoriesAbout this manual Register Your Planar Products TodayTable of contents SETUP AND OPERATIONON-SCREEN DISPLAY OSD MENU SETTINGS MAINTENANCE AND SECURITYSAFETY CERTIFICATIONS PR5020 Projection distance and size tableTIMING MODE TABLE REGULATORY COMPLIANCEPacking Checklist GETTING STARTEDAvoid using the projector in dusty environments Front-right View Views of Projector PartsHeight-adjuster button Push to release height adjusterTop view-On-screen Display OSD buttons and LEDs DLP Projector - User’s ManualUser’s Manual Rear view Bottom view Security LockSecure to permanent object with a Kensington Lock systemRemote Control Parts Page down when connected through USB to a PC Page DownRemote Control Operating Range Projector and Remote Control ButtonsSETUP AND OPERATION Inserting the Remote Control BatteriesConnecting Input Devices User’s Manual Starting and Shutting down the Projector Turn off the main Power switch when the Ready LED stops flashing Setting an Access Password Security Lock Adjusting the Projector Level Adjusting the Zoom, Focus and Keystone Adjusting the VolumeUse the Keystone button to correct image distor- tion ON-SCREEN DISPLAY OSD MENU SETTINGS Navigating the OSDOSD Menu Controls Setting the OSD Language Setting the OSD Language Main Menu InputGamma Main Menu Functions Available for Connected Source x = available to video sourceSetup Menu Functions Available for Connected Source Setup MenuAdvance Feature Data sourceDLP Projector - User’s Manual User Color Config Menu The Config menu functions are available to all video sourcesUtility Menu Utility Menu Functions Available for Connected Source Tool Menu Status Menu TheseMAINTENANCE AND SECURITY Replacing the Projection Lamp2. Open the lamp com- partment cover B 3. Remove the two screws from the lamp module C4. Lift the module handle up D Reverse steps 1 to 5 to install the new lamp module Pull firmly on the mod- ule handle to remove the lamp module DResetting the Lamp Cleaning the ProjectorCleaning the Lens Cleaning the CaseUsing the Kensington Lock TROUBLESHOOTING Common problems and solutionsTips for Troubleshooting LED Error Messages Image ProblemsProblem No image appears on the screen Problem The image is blurredLamp Problems Remote Control ProblemsAudio Problems Problem The image is flat with no contrastSPECIFICATIONS Input/output connectorsPR3010 PR3020PR3020 and PR3010 Projection distance and size table Projection Distance V.S. Projection SizeL Projection Distance PR5020 Projection distance and size table Shaded rows are equivalent measurement in feet and inchesTiming Mode Table SignalResolution VideoProjector Dimensions 300 mm11.8 mm396 244 mm9.6Safety Certifications REGULATORY COMPLIANCEFCC Warning CanadaPlanar Systems, Inc Planar Customer Support