Planar PR5020, PR3020 manual Adjusting the Zoom, Focus and Keystone, Adjusting the Volume

Page 25

Adjusting the Zoom, Focus and Keystone

DLP® Projector – User’s Manual

Adjusting the Zoom, Focus and Keystone

1. Use the Image-zoomcon- trol (on the projector only) to resize the projected im-

age and screen size. B

2. Use the Image-focuscon- trol (on the projector only) to sharpen the projected

image A .

3.

4.

Press the Keystone button on the remote control. The keystone control ap- pears on the display.

Use the Keystone button to correct image distor- tion.

Adjusting the Volume

1. Press the Volume +/- but- ton on the remote control. The volume control ap- pears on the display.

2.

3.

Use the Volume +/- but- ton to adjust the level.

Press the Mute button to turn off the volume. (For remote only)

– 17 –

Image 25

Contents Page Planar Customer Support Planar Systems, IncCorporate Headquarters 1195 NW Compton Drive Beaverton, OR Telephone US 1-866-PLANAR1 866 Outside US 503Copyright User’s ManualDisclaimer Trademark RecognitionSymbols Used Important Safety InformationRemote Control General Safety InformationCleaning the Projector Power SafetySymbol Explanations Replacing the LampCables, Replacement Lamps and Accessories Main FeaturesAbout this manual Register Your Planar Products TodaySETUP AND OPERATION Table of contentsON-SCREEN DISPLAY OSD MENU SETTINGS MAINTENANCE AND SECURITYPR5020 Projection distance and size table SAFETY CERTIFICATIONSTIMING MODE TABLE REGULATORY COMPLIANCEGETTING STARTED Packing ChecklistAvoid using the projector in dusty environments Views of Projector Parts Front-right ViewPush to release height adjuster Height-adjuster buttonTop view-On-screen Display OSD buttons and LEDs DLP Projector - User’s ManualUser’s Manual Rear view Security Lock Bottom viewSecure to permanent object with a Kensington Lock systemRemote Control Parts Page Down Page down when connected through USB to a PCProjector and Remote Control Buttons Remote Control Operating RangeInserting the Remote Control Batteries SETUP AND OPERATIONConnecting Input Devices User’s Manual Starting and Shutting down the Projector Turn off the main Power switch when the Ready LED stops flashing Setting an Access Password Security Lock Adjusting the Projector Level Adjusting the Volume Adjusting the Zoom, Focus and KeystoneUse the Keystone button to correct image distor- tion Navigating the OSD ON-SCREEN DISPLAY OSD MENU SETTINGSOSD Menu Controls Setting the OSD Language User’s Manual Input Main MenuGamma x = available to video source Main Menu Functions Available for Connected SourceSetup Menu Setup Menu Functions Available for Connected SourceData source Advance FeatureDLP Projector - User’s Manual User Color The Config menu functions are available to all video sources Config MenuUtility Menu Utility Menu Functions Available for Connected Source Tool Menu These Status MenuReplacing the Projection Lamp MAINTENANCE AND SECURITY3. Remove the two screws from the lamp module C 2. Open the lamp com- partment cover B4. Lift the module handle up D Pull firmly on the mod- ule handle to remove the lamp module D Reverse steps 1 to 5 to install the new lamp moduleCleaning the Projector Resetting the LampCleaning the Case Cleaning the LensUsing the Kensington Lock Common problems and solutions TROUBLESHOOTINGTips for Troubleshooting Image Problems LED Error MessagesProblem No image appears on the screen Problem The image is blurredRemote Control Problems Lamp ProblemsAudio Problems Problem The image is flat with no contrastInput/output connectors SPECIFICATIONSPR3010 PR3020Projection Distance V.S. Projection Size PR3020 and PR3010 Projection distance and size tableL Projection Distance Shaded rows are equivalent measurement in feet and inches PR5020 Projection distance and size tableSignal Timing Mode TableResolution Video300 mm11.8 mm396 244 mm9.6 Projector DimensionsREGULATORY COMPLIANCE Safety CertificationsFCC Warning CanadaPlanar Customer Support Planar Systems, Inc