Planar PR3020, PR5020 manual Maintenance And Security, Replacing the Projection Lamp

Page 40
MAINTENANCE AND SECURITY

MAINTENANCE AND SECURITY

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

Important:

1.The lamp contains a certain amount of mercury and should be disposed of according to local or- dinance regulations.

2.Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life.

Warning:

Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to do so could result in a severe burn.

Note:

Safety glasses should be worn when replacing the lamp while the projector is ceiling mounted.

1. Loosen the two captive screws on the lamp compartment cover (A).

32

Image 40
Contents Page Planar Systems, Inc Planar Customer SupportCorporate Headquarters 1195 NW Compton Drive Beaverton, OR Telephone US 1-866-PLANAR1 866 Outside US 503User’s Manual CopyrightDisclaimer Trademark RecognitionImportant Safety Information Symbols UsedRemote Control General Safety InformationPower Safety Cleaning the ProjectorSymbol Explanations Replacing the LampMain Features Cables, Replacement Lamps and AccessoriesAbout this manual Register Your Planar Products TodayTable of contents SETUP AND OPERATIONON-SCREEN DISPLAY OSD MENU SETTINGS MAINTENANCE AND SECURITYSAFETY CERTIFICATIONS PR5020 Projection distance and size tableTIMING MODE TABLE REGULATORY COMPLIANCEGETTING STARTED Packing ChecklistAvoid using the projector in dusty environments Front-right View Views of Projector PartsHeight-adjuster button Push to release height adjusterTop view-On-screen Display OSD buttons and LEDs DLP Projector - User’s ManualUser’s Manual Rear view Bottom view Security LockSecure to permanent object with a Kensington Lock systemRemote Control Parts Page down when connected through USB to a PC Page DownRemote Control Operating Range Projector and Remote Control ButtonsSETUP AND OPERATION Inserting the Remote Control BatteriesConnecting Input Devices User’s Manual Starting and Shutting down the Projector Turn off the main Power switch when the Ready LED stops flashing Setting an Access Password Security Lock Adjusting the Projector Level Adjusting the Volume Adjusting the Zoom, Focus and KeystoneUse the Keystone button to correct image distor- tion Navigating the OSD ON-SCREEN DISPLAY OSD MENU SETTINGSOSD Menu Controls Setting the OSD Language Setting the OSD Language Input Main MenuGamma Main Menu Functions Available for Connected Source x = available to video sourceSetup Menu Functions Available for Connected Source Setup MenuAdvance Feature Data sourceDLP Projector - User’s Manual User Color Config Menu The Config menu functions are available to all video sourcesUtility Menu Utility Menu Functions Available for Connected Source Tool Menu Status Menu TheseMAINTENANCE AND SECURITY Replacing the Projection Lamp3. Remove the two screws from the lamp module C 2. Open the lamp com- partment cover B4. Lift the module handle up D Reverse steps 1 to 5 to install the new lamp module Pull firmly on the mod- ule handle to remove the lamp module DResetting the Lamp Cleaning the ProjectorCleaning the Case Cleaning the LensUsing the Kensington Lock Common problems and solutions TROUBLESHOOTINGTips for Troubleshooting LED Error Messages Image ProblemsProblem No image appears on the screen Problem The image is blurredLamp Problems Remote Control ProblemsAudio Problems Problem The image is flat with no contrastSPECIFICATIONS Input/output connectorsPR3010 PR3020Projection Distance V.S. Projection Size PR3020 and PR3010 Projection distance and size tableL Projection Distance PR5020 Projection distance and size table Shaded rows are equivalent measurement in feet and inchesTiming Mode Table SignalResolution VideoProjector Dimensions 300 mm11.8 mm396 244 mm9.6Safety Certifications REGULATORY COMPLIANCEFCC Warning CanadaPlanar Systems, Inc Planar Customer Support