STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page.
Be sure to use only genuine SHARP parts and supplies.
| Indication |
| Cause and remedy | Page |
|
| Steadily | Replacement of drum cartridge will be needed | 70 |
| Drum replacement | lit | soon. Prepare a new cartridge. | |
|
| |||
| required indicator | Blinking | Drum cartridge must be replaced. Replace it with | 58 |
|
| a new one. | ||
| TD cartridge | Steadily | Replacement of TD cartridge will be needed | 70 |
| lit | soon. Prepare a new cartridge. | ||
| replacement |
| ||
|
| TD cartridge must be replaced. Replace it with a |
| |
| required indicator | Blinking | 57 | |
| new one. | |||
|
| |||
|
|
|
|
|
|
|
| A misfeed has occurred. Remove the misfed |
|
| Misfeed indicator | Blinking | paper referring to the description of "MISFEED | 63 |
| REMOVAL". |
| ||
|
|
| The lower side cover may be open. If so, close it. | 66 |
| SPF/RSPF misfeed |
| An original misfeed has occurred in the SPF/ |
|
| Blinking | RSPF. Remove the misfed originals referring to | 66 | |
| indicator |
| the description of "E: Misfeed in the SPF/RSPF". |
|
|
|
|
| |
|
|
|
|
|
|
|
| The unit is in the preheat mode. Press any key to | 54 |
| Power save indicator is | cancel the preheat mode. | ||
|
| |||
| The unit is in the auto power |
| ||
| steadily lit. |
|
| |
|
| Press the start ( ) key to cancel the auto power | 54 | |
|
|
| ||
|
|
|
| |
| The paper tray indicator is | The paper tray is not installed properly. Push the | – | |
| blinking. |
| tray into the unit securely. | |
|
|
| ||
|
|
|
| |
| "CH" is blinking in the | The TD cartridge is not installed. Check if the | 57 | |
| display. |
| cartridge is installed. | |
|
|
| ||
| "CH" is steadily lit in the | Side cover is open. Close the side cover |
| |
| securely by pressing the round projections near | – | ||
| display. |
| ||
|
| the side cover open button. |
| |
|
|
|
| |
|
|
| The paper tray or |
|
|
|
| single bypass has been selected in the printer | 15, 17 |
|
|
| function. | |
|
|
|
| |
| "P" is blinking in the display. | Load paper. |
| |
|
|
| A misfeed has occurred in the paper tray, single |
|
|
|
| bypass or | 63 |
|
|
| paper. |
|
| A letter and a number appear | The scan head locking switch is locked. Unlock |
| |
| the scan head locking switch and turn the power | 9 | ||
| alternately. |
| switch off/on. |
|
|
|
|
| |
|
|
|
|
|
|
|
| The unit will not function. Turn the power switch |
|
| A letter and a number appear | off and then switch it on, and if there is again an | – | |
| alternately. |
| error, remove the power cord from the outlet, and | |
|
|
| ||
|
|
| contact your authorized service representative. |
|
|
|
|
|
|
62