TANDBERG D1320202 manual Debug Commands, Special Commands

Page 27

TANDBERG GWData port Command Interface User Guide

 

 

 

 

 

LastCorrection: 1

 

 

 

 

 

*s/end

 

 

 

4.2.4.

Debug Commands

 

 

 

 

 

 

 

 

 

Command:

Desription:

 

 

 

Syslog

 

Enables a real-time log of Bonding, H.221 and H.323, H324m, ISDN, RTSP, IVider,

 

 

 

 

SIP and IVider Engine activity.

 

 

 

 

Note! Logging via the serial port is limited by the speed of the serial port, which

 

 

 

 

might result in loss of logging data. Therefore, it is advised to use Telnet instead.

 

 

 

 

Syslog <Level> <Mask>

 

 

 

 

Level [0..3]: no logging when level = 0

 

 

 

 

Mask: With this Mask the logging of different components can be turned on. The

 

 

 

 

mask has to be used as a bit mask.

 

 

 

 

FREYALOGH324m

1

 

 

 

 

FREYALOGH323

2

 

 

 

 

FREYALOGISDN

4

 

 

 

 

FREYALOGRTSP

8

 

 

 

 

FREYALOGIVID

16

 

 

 

 

FREYALOGSIP

32

 

 

 

 

FREYALOGENGI

64

 

 

 

 

For instance to view the logging of the H324m, SIP and IVider components, the mask

 

 

 

 

value equals 1 + 16 + 32 = 49

 

 

 

 

 

 

 

 

 

4.2.5.

Special Commands

 

 

 

 

 

 

 

 

 

 

Command:

 

 

Description:

 

 

 

Boot

 

 

 

Reboots the system.

 

 

 

 

 

 

xCommand Boot

 

 

 

 

 

 

 

DefaultValuesSet

 

This command is used to restore factory default settings. Issuing this command

 

 

 

 

 

 

with no parameters will restore all settings except network settings and option

 

 

 

 

 

 

keys.

 

 

 

 

 

 

 

DefaultValuesSet Level: <1 .. 3>

 

 

 

 

 

 

Example (restore all default factory setting):

 

 

 

 

 

 

xCommand DefaultValuesSet

 

 

 

 

 

 

*r Result (status=OK): /

 

 

 

 

 

 

*r/end

 

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

FeedbackRegister

 

Command used to instruct the system to return XML feedback over HTTP(S)

 

 

 

 

 

 

to specific URLs. What parts of the Status and Configuration XML documents

 

 

 

 

 

 

to monitor are specified by XPath expressions. The system supports issuing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

27

 

Image 27
Contents D1320202 Tandberg 3G GWTable of Contents Introduction Hardware and Cabling Tandberg GWTroubleshooting Connecting to the Data port Command Interface using Telnet Xconf H323Gatekeeper ? Command formatCommand types IntroductionCommands Xconf telnet mode onXconf telnet mode H323CallSetup Mode Direct/Gatekeeper System Configuration CommandsCommand Description H323Gatekeeper H323CallSetupEthernet Ethernet speedIsdn Https HttpSnmp Telnet SSHTandberg GW Command Description Gateway General GW CommandsNTP SIP Tandberg GW Example of SS7 feedback Tandberg GW VideoPortal Mode On/Off or System 1 . IP Address IPAddrPRI System Status CommandsTemperatureCelcius TemperatureFahrenheitDNS Status Address Port Address ProtocolURL PRI BRIStatus Feedback 1Feedback GatewayCallCall Status Address Port Last Update Last CorrectionSystemLoad SystemLoad Call 1Special Commands Debug CommandsOK Result parameters Error Result parametersParameters Expression 1 . S 0, 256 XPath expressionOptionKeyDelete ServiceEntryDeleteParameters ServiceEntryNumberr Example Delete Service nr ServiceEntrySwapExamples XhistoryXhistory ? Tandberg GW Index Commands