TANDBERG D1320202 manual Ethernet speed, Isdn

Page 10

TANDBERG GWData port Command Interface User Guide

 

 

DNS Server: Number identifying one of 5 DNS servers which

 

 

 

can be configured. If this parameter is omitted the command

 

 

 

applies to the first configuration (1).

 

 

 

sub-commands:

 

 

 

Assignment: Selects between DHCP (Dynamic Host

 

 

 

Configuration Protocol) or static IP address allocation. When

 

 

 

DHCP is selected the GW will automatically receive all the

 

 

 

necessary information from the DHCP server. This function

 

 

 

should be used when the GW is connected to a LAN using

 

 

 

DHCP. When using this mode, IP-address and IP-subnet mask

 

 

 

are not used because the DHCP server supplies these parameters.

 

 

 

Address: Sets the static IP address for the given LAN interface.

 

 

 

Subnetmask: Sets the subnet mask variable. Subnet mask

 

 

 

defines the network class. If the setting is 255.255.255.0 the local

 

 

 

network will support up to 256 nodes, denoting a class C

 

 

 

network. If the setting is 255.255.0.0 the local network is a class

 

 

 

B network with 65536 addressable nodes.

 

 

 

Gateway: Sets the gateway IP address. If a gateway is located on

 

 

 

the LAN and the GW needs to reach nodes through this gateway,

 

 

 

the gateway address can be set using the gateway variable (the IP

 

 

 

address of the gateway will be set automatically if the GW is in

 

 

 

DHCP mode)

 

 

 

Domain Name: Sets the domain name string of which the

 

 

 

gateway is part of. Minimum 0, maximum 64 characters.

 

 

 

Example of IP Address feedback:

 

 

 

*c xConfiguration IP Address: "127.0.0.1"

 

 

 

 

 

 

Ethernet

Sets LAN port speed.

 

 

 

NOTE! The GW needs to reboot before the changes will apply.

 

 

 

Ethernet <speed>

 

 

 

---

 

 

 

parameters:

 

 

 

speed: auto/10half/10full/100half/100full. The speed is either

 

 

 

set to auto or manually from 10mb half duplex to 100mb full

 

 

 

duplex. When set to auto the GW will automatically negotiate

 

 

 

with the network and use the best available setting.

 

 

 

Example of Ethernet feedback:

 

 

 

*c xConfiguration Ethernet Speed: Auto

 

 

 

 

 

 

ISDN

Defines various ISDN protocol settings.

 

 

 

ISDN IncomingBearerCapability: <UDI/All>

 

 

 

or

 

 

 

ISDN OutgoingBearerCapability: <H324m/UDI>

 

 

 

or

 

 

 

ISDN BRI SwitchType: <NI/ATT/Euro/Japan>

 

 

 

or

 

 

 

ISDN PRI SwitchType: <NI/ATT/Euro/Japan>

 

 

 

or

 

 

 

ISDN PRI Interface LowChannel: <1..31>

 

 

 

---

 

 

 

Parameters:

 

 

 

sub-commands:

 

 

 

 

 

 

 

10

 

Image 10
Contents Tandberg 3G GW D1320202Table of Contents Introduction Tandberg GW Hardware and CablingTroubleshooting Connecting to the Data port Command Interface using Telnet Introduction Command formatCommand types Xconf H323Gatekeeper ?Xconf telnet mode on CommandsXconf telnet mode H323CallSetup System Configuration CommandsCommand Description H323Gatekeeper H323CallSetup Mode Direct/GatekeeperEthernet speed EthernetIsdn Http HttpsSnmp SSH TelnetTandberg GW General GW Commands Command Description GatewayNTP SIP Tandberg GW Example of SS7 feedback Tandberg GW Mode On/Off or System 1 . IP Address IPAddr VideoPortalTemperatureFahrenheit System Status CommandsTemperatureCelcius PRIDNS Address Protocol Status Address PortURL BRI PRIGatewayCall Feedback 1Feedback StatusSystemLoad Call 1 Status Address Port Last Update Last CorrectionSystemLoad CallDebug Commands Special CommandsExpression 1 . S 0, 256 XPath expression Error Result parametersParameters OK Result parametersServiceEntrySwap ServiceEntryDeleteParameters ServiceEntryNumberr Example Delete Service nr OptionKeyDeleteXhistory ExamplesXhistory ? Tandberg GW Index Commands