TANDBERG T1 manual Sharing a PC presentation, Shows the PC presentation and the participants

Page 44

T1

Contents

Introduction

Getting started

Sharing a PC presentation

General recommendations for the executive meeting room and executive office are described on the previous page.

Dual video stream

With dual video stream you can view two different live video streams simultaneously, the main video and one additional source. This could for example be both a PC presentation and the person who gives the presentation.

If one of the video systems does not support Dual Video Stream, no second video stream will be established and the PC presentation will be shown as the main video.

Sharing the presentation

1.Make sure the PC do not cover any of the microphones as this will reduce the audio quality at the far end

2.Locate the DVI cable and connect the PC to the video system

3. When pressing the PC button ( ) on the remote control the default presentation source is activated.

The DVI/VGA input is compliant with VESA Extended Display Identification Data (EDID) and will be able to notify the PC of the supported output formats.

Troubleshooting if the presentation does not show

On most PC’s you must press a special key combination to switch

 

the PC image from the PC screen to the video screen

Make sure the connector used for PC presentation is configured as

 

the default presentation source.

 

Go to: Home > Administrator settings > Advanced

Administrator Guide

About the menus

About the settings

Settings Library

Cameras

 

AppenAppendicesi

Contact us

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Shows the PC presentation and the participants

PC

configurations > Video > DefaultPresentationSource (the

default value is 3, and corresponds to ...Video > Input > Source 3)

Make sure your PC is set to activate your VGA output

Other presentation sources

You can also connect other presentation sources like:

DVD

Document camera

The screen layout

Press the Layout button on the remote control to select a suitable layout on screen.

The default layout when showing a PC presentation is designed to allow the participants to keep eye contact with each other during the presentation.

Default layout with a wide signal in from the PC (currently only supported on digital input)

Default layout with a 4/3 signal in from the PC.

D14274.01—NOVEMBER 2008

44

Image 44
Contents Tandberg T1 NovemberTable of Contents What’s in this guide?This chapter IntroductionChapter Tandberg T1 at a glance Intellectual Property Rights TrademarkDisclaimer Patent InformationSafety Instructions Water and MoistureEnvironmental Issues TANDBERG’s Environmental PolicyGetting started System overview Cable configurations LANUsing the Remote Control BatteriesUsing the Remote Control, Call KEYIf you need to set a static IP address Verify IP address settingsTurn on the system Add the system to the network Verify your settingsTime zone settings About the menus Settings The Settings menu Administrator settings menuAbout the menus Home The Home menuSettings menu Explaining the administrator settingsAdministrator settings IP Settings menuAdvanced configuration menu SearchAdministrator Settings Library SIPAdvanced configuration menu Audio settingsAudio Output Hdmi 1, 3 Mode On/Off Audio Output Line 1. Mode On/OffAudio Input Line 1. Level Audio Input Line 1. Channel Left/Right/MonoCamera settings Conference settings Do not disturb setting Network settings Network services settings NetworkServices Snmp Mode Off/ReadOnly/ReadWrite NetworkServices Snmp CommunityName S 0NetworkServices Snmp SystemContact S 0 NetworkServices Snmp SystemLocation S 0Serial port settings Phone book server settingsProvisioning settings SIP Profile settings Standby settingsSystem unit settings Time zone settingVideo OSD Mode On/Off Video Input Source 2 Connector HDMI/HDSDI/YPbPrVideo Input Source 1. CameraControl Mode On/Off Video Input Source 1 Connector HDMI/HDSDI/YPbPrVideo Output Composite 5 Resolution PAL/NTSC Example Video Output Hdmi 1 ResolutionExample Video Output DVI 2 Resolution Example Video Output Composite 5 Resolution NtscCameras PrecisionHD 1080p camera Hdmi and HD-SDIKensington lock Cascaded camerasConnecting the camera Tandberg T1Tandberg TRC5 Using Best viewBest view-Face recognition Line voltage frequency DIP switch settings for video output formatsVideo output formats Cameras in daisy chain Appendices Tandberg DnamGeneral room guidelines Physical conditionsRoom equipment Environmental considerationsAudio quality Natural communicationBest audio quality to all participants Making eye contactGuidelines for the telepresence room setup Adjust the camera viewGeneral recommendations for the room layout Distance between the table and the video systemSharing a PC presentation Shows the PC presentation and the participantsGuidelines for the high end meeting room setup Camera viewAdministrator Guide Tandberg Remote Control TRC5 ArrowsConfigure the video inputs Administrator settingsAPI commands Video Input MatrixSoftware upgrade Software upgrade procedureUpload certificates Certificates upload procedureHow to upload the certificate Configuration CommandXML files View XML filesLog files Debug log filesDnam Loudspeaker Cabinet Dnam AmplifierNTP Time Zone expressions NTP Time Zone expressions, GMT+0 GMT0NZ-CHAT CETMedia capabilities supported in SIP Supported RFCs in SIPCurrent RFCs and drafts supported in SIP CE Declaration for Telepresence T1 China RoHS table Tandberg T1 dimensions Front viewLeft side view Top viewPrecisionHD 1080p camera dimensions PAL/NTSC Technical specificationsUnit Delivered Complete with HTTP, Https TCP/IP DhcpGpio Headquarters European Headquarters Tandberg