TANDBERG T1 NetworkServices Snmp Mode Off/ReadOnly/ReadWrite, NetworkServices H323 Mode On/Off

Page 28

T1

Contents

Introduction

Getting started

About the menus

About the settings

Administrator Guide

 

TheS ttingssettingsLibralibraryy

Cameras

Appendices

Contact us

 

 

 

 

 

NetworkServices SNMP Mode: <Off/ReadOnly/ReadWrite>

SNMP (Simple Network Management Protocol) is used in network management systems to monitor network-attached devices (routers, servers, switches, projectors, etc) for conditions that warrant administrative attention. SNMP exposes management data in the form of variables on the managed systems, which describe the system configuration. These variables can then be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by managing applications.

Off: Set to Off when you want to disable the SNMP network service.

ReadOnly: Set to ReadOnly when you want to enable the SNMP network service for queries only.

ReadWrite: Set to ReadOnly when you want to enable the SNMP network service for both queries and commands.

Example: NetworkServices SNMP Mode: ReadWrite

NetworkServices SNMP CommunityName: <S: 0, 50>

Enter the name of the Network Services SNMP Community. SNMP Community names are used to authenticate SNMP requests. SNMP requests must have a ‘password’ (case sensitive) in order to receive a response from the SNMP Agent in the codec. The default password is “public”. If you have the TANDBERG Management Suite (TMS) you must make sure the same SNMP Community is configured there too. Note! The SNMP Community password is case sensitive.

Format: String with a maximum of 50 characters.

Example: NetworkServices SNMP CommunityName: “public”

NetworkServices SNMP SystemContact: <S: 0, 50>

Enter the name of the Network Services SNMP System Contact.

Format: String with a maximum of 50 characters.

Example: NetworkServices SNMP SystemContact: “”

NetworkServices SNMP SystemLocation: <S: 0, 50>

Enter the name of the Network Services SNMP System Location.

Format: String with a maximum of 50 characters.

Example: NetworkServices SNMP SystemLocation: “”

NetworkServices SNMP HostIpAddress [1..3]: <S: 0, 64>

Enter the IP address of up to three SNMP Managers. All traps will then be sent to the hosts listed.

The system’s SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC program etc.). SNMP Traps are generated by the SNMP Agent to inform the SNMP Manager about important events. Can be used to send event created messages to the SNMP agent about different events like: system reboot, system dialing, system disconnecting, MCU call, packet loss etc. Traps can be sent to multiple SNMP Trap Hosts.

Format: String with a maximum of 64 characters.

Example: NetworkServices SNMP HostIpAddress 1: “”

NetworkServices H323 Mode: <On/Off>

Determines whether the system should be able to place and receive H.323 calls.

On: Set to On to enable the possibility to place and receive H.323 calls.This is the default setting.

Off: Set to Off to disable the possibility to place and receive H.323 calls. NOTE! Changes in this setting requires the codec to be restarted.

Example: NetworkServices H323 Mode: On

NetworkServices SIP Mode: <On/Off>

Determines whether the system should be able to place and receive SIP calls.

On: Set to On to enable the possibility to place and receive SIP calls.This is the default setting.

Off: Set to Off to disable the possibility to place and receive SIP calls. NOTE! Changes in this setting requires the codec to be restarted.

Example: NetworkServices SIP Mode: On

NetworkServices NTP Mode: <Auto/Manual>

The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server. The time server will subsequently be queried every 24th hour for time updates. The time will be displayed on the top of the screen. The system will use the time to timestamp messages transmitted to Gatekeepers or Border Controllers requiring H.235 authentication. The system will use the time to timestamp messages transmitted to Gatekeepers or Border Controllers that requires H.235 authentication. It is also used for timestamping Placed Calls, Missed Calls and Received Calls.

Auto: The system will use the NTP server, by which address is supplied from the DHCP server in the network. If no DHCP server is used, or the DHCP server does not provide the system with a NTP server address, the system will use the static defined NTP server address specified by the user.

Manual: The system will always use the static defined NTP server address specified by the user.

Example: NetworkServices NTP Mode: Manual

NetworkServices NTP Address: <S: 0, 64>

Enter the NTP Address to define the network time protocol server address. This address will be used if NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.

Format: String with a maximum of 64 characters.

Example: NetworkServices NTP Address: “1.tandberg.pool.ntp.org”

D14274.01—NOVEMBER 2008

28

Image 28
Contents Tandberg T1 NovemberTable of Contents What’s in this guide?Chapter IntroductionThis chapter Tandberg T1 at a glance Intellectual Property Rights TrademarkDisclaimer Patent InformationSafety Instructions Water and MoistureEnvironmental Issues TANDBERG’s Environmental PolicyGetting started System overview Cable configurations LANUsing the Remote Control BatteriesUsing the Remote Control, Call KEYTurn on the system Verify IP address settingsIf you need to set a static IP address Time zone settings Verify your settingsAdd the system to the network About the menus Settings The Settings menu Administrator settings menuAbout the menus Home The Home menuSettings menu Explaining the administrator settingsAdministrator settings IP Settings menuAdvanced configuration menu SearchAdministrator Settings Library SIPAdvanced configuration menu Audio settingsAudio Output Hdmi 1, 3 Mode On/Off Audio Output Line 1. Mode On/OffAudio Input Line 1. Level Audio Input Line 1. Channel Left/Right/MonoCamera settings Conference settings Do not disturb setting Network settings Network services settings NetworkServices Snmp Mode Off/ReadOnly/ReadWrite NetworkServices Snmp CommunityName S 0NetworkServices Snmp SystemContact S 0 NetworkServices Snmp SystemLocation S 0Provisioning settings Phone book server settingsSerial port settings SIP Profile settings Standby settingsSystem unit settings Time zone settingVideo OSD Mode On/Off Video Input Source 2 Connector HDMI/HDSDI/YPbPrVideo Input Source 1. CameraControl Mode On/Off Video Input Source 1 Connector HDMI/HDSDI/YPbPrVideo Output Composite 5 Resolution PAL/NTSC Example Video Output Hdmi 1 ResolutionExample Video Output DVI 2 Resolution Example Video Output Composite 5 Resolution NtscCameras PrecisionHD 1080p camera Hdmi and HD-SDIKensington lock Cascaded camerasConnecting the camera Tandberg T1Best view-Face recognition Using Best viewTandberg TRC5 Video output formats DIP switch settings for video output formatsLine voltage frequency Cameras in daisy chain Appendices Tandberg DnamGeneral room guidelines Physical conditionsRoom equipment Environmental considerationsAudio quality Natural communicationBest audio quality to all participants Making eye contactGuidelines for the telepresence room setup Adjust the camera viewGeneral recommendations for the room layout Distance between the table and the video systemSharing a PC presentation Shows the PC presentation and the participantsGuidelines for the high end meeting room setup Camera viewAdministrator Guide Tandberg Remote Control TRC5 ArrowsConfigure the video inputs Administrator settingsAPI commands Video Input MatrixSoftware upgrade Software upgrade procedureHow to upload the certificate Certificates upload procedureUpload certificates Configuration CommandXML files View XML filesLog files Debug log filesDnam Loudspeaker Cabinet Dnam AmplifierNTP Time Zone expressions NTP Time Zone expressions, GMT+0 GMT0NZ-CHAT CETCurrent RFCs and drafts supported in SIP Supported RFCs in SIPMedia capabilities supported in SIP CE Declaration for Telepresence T1 China RoHS table Tandberg T1 dimensions Front viewLeft side view Top viewPrecisionHD 1080p camera dimensions Unit Delivered Complete with Technical specificationsPAL/NTSC Gpio TCP/IP DhcpHTTP, Https Headquarters European Headquarters Tandberg