Runco VX-50d, VX-40d, VX-80d manual VX-60d/-80d Lens Options and Throw Ratios

Page 33

Installation

Throw Distance Ranges - VX-60d/-80d:Table 3-4lists the available lens options for the VX-60d/-80d and their associated throw ratios.

Table 3-4. VX-60d/-80d Lens Options and Throw Ratios

 

Throw Ratio

Throw Distance Range

 

(in inches, with 100-inch Wide Screen)

Lens Option (Note 2)

(Throw Dist.

 

Screen Width)

Minimum

Maximum

 

 

 

 

 

 

 

 

Telesto A

0.75 (Fixed)

 

For rear-screen installations only. Contact

 

 

 

Runco Technical Support for more information.

 

 

 

 

 

Telesto B

1.48 - 1.75

 

148

175

 

 

 

 

 

Telesto C

1.81 - 2.40

 

181

240

 

 

 

 

 

Telesto C with CineWide

1.79 - 1.86

 

179

186

(16:9 screen)

 

 

 

 

 

 

 

 

 

Telesto D

2.56 - 4.35

 

256

435

 

 

 

 

 

Telesto D with CineWide

1.95 - 3.23

 

195

323

(16:9 screen)

 

 

 

 

 

 

 

 

 

Telesto E

4.48 - 7.11

 

448

711

 

 

 

 

 

Telesto E with CineWide

3.40 - 5.31

 

340

531

(16:9 screen)

 

 

 

 

 

 

 

 

 

Telesto E with CineWide

2.55 - 4.00

 

255

400

(2.35:1 screen) (Note 3)

 

 

 

 

 

 

 

 

 

Notes:

1. Throw distance does not affect image quality, provided these ranges are taken into account.

2. Only the Telesto C, D and E lenses can be used with the optional CineWide (secondary anamorphic) lens. Doing so affects the throw distances as shown here.

3. Due to optical and mechanical limitations, this lens combination is available only as a fixed CineWide configuration. CineWide with AutoScope is not supported.

Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

21

Image 33
Contents VX-40d / VX-50d VX-60d / VX-80d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Specifications Maintenance and TroubleshootingOperation Serial CommunicationsTable of Contents List of Figures Xii About This Manual Certain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Runco Optional AccessoriesVX-40d/-50d/-60d/-80d Top/Rear/Front View VX-40d/-50d/-60d/ -80d at a GlanceVX-40d/-50d/-60d/ -80d Input Panel Rear Foot Stationary Power Input 100 to 240 VACRS232 OUT Not used RS422 Not used Gpio Not used RS232Input 3 Video / Input 4 S-Video Input 2 DVIFocus VX-40d/-50d/-60d/ -80d Rear-Panel KeypadZoom VX-40d/-50d/-60d/-80d has its own internal menu systemInput 1 BNC Menu Navigation ButtonsHelp ExitDHD Controller Front Panel DHD Controller Front PanelOutputs DHD Controller Rear PanelComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsInputs 3. DVI 1 / DVI 2 Digital Video 1 / S-VIDEODHD Controller Remote ControlCursor Buttons On / OFFFor more information about aspect ratios, refer to Table VideoAspect Ratio Selection Buttons Memory Preset Buttons ISF NT NightANA Anamorphic 4X3 Standard 43Controls and Functions Installation Installation Overview Quick SetupInstallation specialist Step Procedure For Details, Refer toProjector Installation Options Installation ConsiderationsInstallation Type Ambient LightThrow Ratio Throw Distance Range VX-40d/-50d Lens Options and Throw RatiosLens Option Note Throw Dist Minimum MaximumLens Option Note Throw Dist Screen Width Minimum Maximum VX-60d/-80d Lens Options and Throw RatiosPosition Vertical and HorizontalScreen center are aligned with each other Horizontal Lens ShiftFolded Optics Lens Assembly Front View Installing the Projection LensInstalling the Optional CineWide Lens Mount AutoScope or Base PlateFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Mounting VX-40d/-50d/-60d/ -80d Adjusting the ProjectionFloor Mounting Ceiling MountingConnecting the DHD Controller to VX-40d/-50d/-60d/-80d Connector Panel AccessConnecting Source 10. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See Figure11. Analog RGB Connections Analog Computer RGB Connections See Figure12. Composite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureRS-232 Controller Connecting 12-VoltConnection Trigger Outputs toInput voltage to the AutoScope lens motor must be between Connecting to AC PowerTurning on the Power You must enter a passcode to access the Service menuSelecting the Input Source Focus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsAssembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or BaseHorizontal Position X Adjustment Too Low Correct position Too High Geometry Wrong Position Correct PositionCalibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Are disabled Channel SetupNavigating the Projector Menus 17. Copying a Channel You cannot use Auto Setup with a locked channel. Copy Auto SetupNative aspect ratio is with the primary lens only. With an 18. Resize Presets No ResizingInstallation Adjust Pixel Tracking before Pixel Phase Values shown represent where the approximate centerRecommended see below Input Levels are not applicable to DVI Input Experienced technicians use the Input Levels submenuOn an internal grayscale test pattern Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentOriginally expected may no longer be possible Working With the LampIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Operation Using the On-Screen MenusService ISF PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio HD Pass Thru 1 HD Pass ThruRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Serial Number Hardware Firmware 0002.003A Date Mar 15Calibration You must enter a passcode to access the Calibration menuOperation Input Names Restore Composite Video Component SD ServiceTip ADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Removing the Lamp Door Lamp and Filter ReplacementRemoving the Lamp Lamp is accurate Recording the Serial Number of a New LampRemoving the Primary Lens Lens ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Power down the projector VX-40d/-50d/-60d/-80d Error Codes Error CodesCode Description General Code Description Lamp Failures Power and CoolingCode Description Tipm Image Processor Built-In KeypadPanel Driver and Formatter Code Description Miscellaneous Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands CommandVIRTUAL235 YES Aspect Ratio CommandsImage Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Serial Communications VX-40d/-50d/-60d/-80d Specifications VX-40d/-50d/-60d/ -80d SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements VX-40d/-60d VX-50d/-80dWeight without lens DimensionsLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-40d/-50d/-60d/-80d Dimensions VX-40d/-50d/-60d/ -80d DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual