Runco VX-40d, VX-50d, VX-80d, VX-60d manual Operation

Page 84

Operation

To configure a trigger to activate when the system is turned on –

Tip for example, when using the trigger to control a retractable screen

– assign that trigger to all aspect ratios.

To save the trigger settings so that they can be restored after a System Reset (described below), press repeatedly to highlight “Save.” Then, press ENTER.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD language. (Currently, only English is supported.)

•Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

•Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

•Side Bar Color: This controls the color of the inactive image area. The range is from -100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the Standard 4:3 aspect ratio, and above and below the active image area when using the Letterbox aspect ratio.

•Film Mode: Enable Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the DHD Controller detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to enable Film Mode to ensure stable processing for that source.

Resolution: The DHD Controller defaults to an output resolution of 720p. When using the VX-40d/-50d/-60d/-80d with a computer or certain HD sources, you may want to force the DHD Controller to use a different output resolution. If so, select Resolution from the Service menu and choose one. Then, press ENTER to confirm.

System Reset: To reset ALL projector and controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears, reminding you to save your settings before you perform the reset, so that you can restore them afterwards. If you have done this, select Confirm to continue with the reset. Otherwise, click Back to cancel.

This action is not undoable. Proceed with caution! Before you Caution perform a System Reset, save ALL settings, including “Custom” ISF

Presets (page 66), ISF Day/Night presets (page 68), Output Shift settings (page 68), Input Names (page 69) and Trigger settings (page 71).

Restore Saved Settings: Following a System Reset, select Restore Saved Settings to apply all previously-saved settings to the projector and DHD Controller.

72

Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

Page 83 Page 85
Image 84
Page 83 Page 85
Contents VX-40d / VX-50d VX-60d / VX-80d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsTable of Contents List of Figures Xii About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories RuncoVX-40d/-50d/-60d/ -80d at a Glance VX-40d/-50d/-60d/-80d Top/Rear/Front ViewRear Foot Stationary Power Input 100 to 240 VAC VX-40d/-50d/-60d/ -80d Input PanelRS232 RS232 OUT Not used RS422 Not used Gpio Not usedInput 3 Video / Input 4 S-Video Input 2 DVIVX-40d/-50d/-60d/ -80d Rear-Panel Keypad FocusZoom VX-40d/-50d/-60d/-80d has its own internal menu systemMenu Navigation Buttons Input 1 BNCHelp ExitDHD Controller Front Panel DHD Controller Front PanelDHD Controller Rear Panel OutputsHD1 / HD2 Analog BNC connectors Component Video RCA connectorsInputs 3. DVI 1 / DVI 2 Digital Video 1 / S-VIDEORemote Control DHD ControllerOn / OFF Cursor ButtonsFor more information about aspect ratios, refer to Table VideoMemory Preset Buttons ISF NT Night Aspect Ratio Selection ButtonsANA Anamorphic 4X3 Standard 43Controls and Functions Installation Quick Setup Installation OverviewInstallation specialist Step Procedure For Details, Refer toInstallation Considerations Projector Installation OptionsInstallation Type Ambient LightVX-40d/-50d Lens Options and Throw Ratios Throw Ratio Throw Distance RangeLens Option Note Throw Dist Minimum MaximumVX-60d/-80d Lens Options and Throw Ratios Lens Option Note Throw Dist Screen Width Minimum MaximumVertical and Horizontal PositionHorizontal Lens Shift Screen center are aligned with each otherFolded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount AutoScope or Base PlateFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Adjusting the Projection Mounting VX-40d/-50d/-60d/ -80dFloor Mounting Ceiling MountingConnector Panel Access Connecting the DHD Controller to VX-40d/-50d/-60d/-80dConnecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toConnecting to AC Power Input voltage to the AutoScope lens motor must be betweenTurning on the Power You must enter a passcode to access the Service menuSelecting the Input Source Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or BaseHorizontal Position X Adjustment Too Low Correct position Too High Wrong Position Correct Position GeometryCalibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Are disabled Channel SetupNavigating the Projector Menus 17. Copying a Channel Auto Setup You cannot use Auto Setup with a locked channel. Copy18. Resize Presets No Resizing Native aspect ratio is with the primary lens only. With anInstallation Adjust Pixel Tracking before Pixel Phase Values shown represent where the approximate centerRecommended see below Input Levels are not applicable to DVI Input Experienced technicians use the Input Levels submenuOn an internal grayscale test pattern There must be at least two consecutive white pixels present Uncheck this item before exiting this menuWorking With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Using the On-Screen Menus OperationISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.003A Date Mar 15You must enter a passcode to access the Calibration menu CalibrationOperation Service Input Names Restore Composite Video Component SDTip ADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Recording the Serial Number of a New Lamp Lamp is accurateLens Replacement Removing the Primary LensTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Power down the projector VX-40d/-50d/-60d/-80d Error Codes Error CodesCode Description General Power and Cooling Code Description Lamp FailuresCode Description Tipm Image Processor Built-In KeypadPanel Driver and Formatter Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands CommandAspect Ratio Commands VIRTUAL235 YESImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Serial Communications VX-40d/-50d/-60d/ -80d Specifications VX-40d/-50d/-60d/-80d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements VX-40d/-60d VX-50d/-80dDimensions Weight without lensLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-40d/-50d/-60d/ -80d Dimensions VX-40d/-50d/-60d/-80d DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents