Runco VX-60d, VX-40d, VX-50d, VX-80d manual Gray Yellow Cyan Green Magenta Red Blue

Page 75

Operation

Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-3.

Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast

Select Contrast and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size.

Brightness and contrast controls are interactive. A change to one

Note may require a subtle change to the other in order to achieve the optimum setting.

Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4.

gray

yellow

cyan

green

magenta

red

blue

Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

63

Image 75

Contents VX-40d / VX-50d VX-60d / VX-80d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Serial Communications Maintenance and TroubleshootingSpecifications OperationTable of Contents List of Figures Xii About This Manual Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationDescription, Features and Benefits Runco Optional AccessoriesVX-40d/-50d/-60d/-80d Top/Rear/Front View VX-40d/-50d/-60d/ -80d at a GlanceVX-40d/-50d/-60d/ -80d Input Panel Rear Foot Stationary Power Input 100 to 240 VACInput 2 DVI RS232RS232 OUT Not used RS422 Not used Gpio Not used Input 3 Video / Input 4 S-VideoVX-40d/-50d/-60d/-80d has its own internal menu system VX-40d/-50d/-60d/ -80d Rear-Panel KeypadFocus ZoomExit Menu Navigation ButtonsInput 1 BNC HelpDHD Controller Front Panel DHD Controller Front PanelOutputs DHD Controller Rear PanelVideo 1 / S-VIDEO HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors Inputs 3. DVI 1 / DVI 2 DigitalDHD Controller Remote ControlVideo On / OFFCursor Buttons For more information about aspect ratios, refer to Table4X3 Standard 43 Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons ANA AnamorphicControls and Functions Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation specialistAmbient Light Installation ConsiderationsProjector Installation Options Installation TypeMinimum Maximum VX-40d/-50d Lens Options and Throw RatiosThrow Ratio Throw Distance Range Lens Option Note Throw DistLens Option Note Throw Dist Screen Width Minimum Maximum VX-60d/-80d Lens Options and Throw RatiosPosition Vertical and HorizontalScreen center are aligned with each other Horizontal Lens ShiftFolded Optics Lens Assembly Front View Installing the Projection LensInstalling the Optional CineWide Lens Mount AutoScope or Base PlateFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Ceiling Mounting Adjusting the ProjectionMounting VX-40d/-50d/-60d/ -80d Floor MountingConnecting the DHD Controller to VX-40d/-50d/-60d/-80d Connector Panel AccessConnecting Source 10. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See Figure11. Analog RGB Connections Analog Computer RGB Connections See Figure12. Composite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureTrigger Outputs to Connecting 12-VoltRS-232 Controller ConnectionInput voltage to the AutoScope lens motor must be between Connecting to AC PowerTurning on the Power You must enter a passcode to access the Service menuSelecting the Input Source Focus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens AdjustmentsWith AutoScope or Base Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor Carriage Plate CineWideHorizontal Position X Adjustment Too Low Correct position Too High Geometry Wrong Position Correct PositionCalibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Are disabled Channel SetupNavigating the Projector Menus 17. Copying a Channel You cannot use Auto Setup with a locked channel. Copy Auto SetupNative aspect ratio is with the primary lens only. With an 18. Resize Presets No ResizingInstallation Adjust Pixel Tracking before Pixel Phase Values shown represent where the approximate centerRecommended see below Input Levels are not applicable to DVI Input Experienced technicians use the Input Levels submenuOn an internal grayscale test pattern Uncheck this item before exiting this menu There must be at least two consecutive white pixels presentOriginally expected may no longer be possible Working With the LampIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Left/Right Up/Down Width Height Overscan Serial Number Hardware Firmware 0002.003A Date Mar 15 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration You must enter a passcode to access the Calibration menuOperation Input Names Restore Composite Video Component SD ServiceTip ADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Removing the Lamp Door Lamp and Filter ReplacementRemoving the Lamp Lamp is accurate Recording the Serial Number of a New LampRemoving the Primary Lens Lens ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Power down the projector VX-40d/-50d/-60d/-80d Error Codes Error CodesCode Description General Code Description Lamp Failures Power and CoolingCode Description Tipm Image Processor Built-In KeypadPanel Driver and Formatter Code Description Miscellaneous Command RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommandsVIRTUAL235 YES Aspect Ratio CommandsImage Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Serial Communications VX-40d/-50d/-60d/-80d Specifications VX-40d/-50d/-60d/ -80d SpecificationsVX-50d/-80d Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements VX-40d/-60dSpecifications are subject to change without notice DimensionsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsVX-40d/-50d/-60d/-80d Dimensions VX-40d/-50d/-60d/ -80d DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual