Runco VX-80d On / OFF, Cursor Buttons, For more information about aspect ratios, refer to Table

Page 26

Controls and Functions

1.IR OUTPUT INDICATOR

Lights when a button is pressed to indicate that an IR signal is being transmitted.

2.ON / OFF

Press to turn the projector on or off.

3.ENTER

Press to select a highlighted menu item or confirm a changed setting.

4.Cursor Buttons (, , , )

Use these buttons to select items or settings, adjust settings or switch display patterns.

When no menus are present on-screen, the UP and DOWN buttons toggle through the available aspect ratios, in this order:

UP Button = Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema - Virtualwide 2.35

DOWN Button = Virtualwide 2.35 - Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic

Note	Virtualwide 2.35 is available only on CineWide-equipped projectors.
	For more information about aspect ratios, refer to Table 4-1.

Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this order:

LEFT Button = HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 - HD/RGB 1 - Component SD - S-Video 2 - S-Video 1 - Composite

RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1 - DVI 2 - HD Pass Thru 1 - HD Pass Thru 2

5.LIGHT

Press to illuminate the buttons.

6.MENU

Press this button to access the OSD controls, or to exit the current menu and return to the previous one.

7.VIDEO (1)

Press to select Composite video input as the source or to enter the numeric character “1.”

8.COMP (Component) (2)

Press to select Component SD (480i/576i) video input as the source or to enter the numeric character “2.”

14	Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

Image 26

Contents VX-40d / VX-50d VX-60d / VX-80d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents List of Figures Xii About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories RuncoVX-40d/-50d/-60d/ -80d at a Glance VX-40d/-50d/-60d/-80d Top/Rear/Front ViewRear Foot Stationary Power Input 100 to 240 VAC VX-40d/-50d/-60d/ -80d Input PanelInput 3 Video / Input 4 S-Video RS232RS232 OUT Not used RS422 Not used Gpio Not used Input 2 DVIZoom VX-40d/-50d/-60d/ -80d Rear-Panel KeypadFocus VX-40d/-50d/-60d/-80d has its own internal menu systemHelp Menu Navigation ButtonsInput 1 BNC ExitDHD Controller Front Panel DHD Controller Front PanelDHD Controller Rear Panel OutputsInputs 3. DVI 1 / DVI 2 Digital HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors Video 1 / S-VIDEORemote Control DHD ControllerFor more information about aspect ratios, refer to Table On / OFFCursor Buttons VideoANA Anamorphic Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons 4X3 Standard 43Controls and Functions Installation Installation specialist Quick SetupInstallation Overview Step Procedure For Details, Refer toInstallation Type Installation ConsiderationsProjector Installation Options Ambient LightLens Option Note Throw Dist VX-40d/-50d Lens Options and Throw RatiosThrow Ratio Throw Distance Range Minimum MaximumVX-60d/-80d Lens Options and Throw Ratios Lens Option Note Throw Dist Screen Width Minimum MaximumVertical and Horizontal PositionHorizontal Lens Shift Screen center are aligned with each otherFolded Optics Installing the Projection Lens Lens Assembly Front ViewFixed CineWide Are both fully assembled Installing the Optional CineWide Lens MountAutoScope or Base Plate AutoScope stand used for floor-mounted projector Floor Mounting Adjusting the ProjectionMounting VX-40d/-50d/-60d/ -80d Ceiling MountingConnector Panel Access Connecting the DHD Controller to VX-40d/-50d/-60d/-80dConnecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsConnection Connecting 12-VoltRS-232 Controller Trigger Outputs toConnecting to AC Power Input voltage to the AutoScope lens motor must be betweenSelecting the Input Source Turning on the PowerYou must enter a passcode to access the Service menu Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftCarriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or BaseHorizontal Position X Adjustment Too Low Correct position Too High Wrong Position Correct Position GeometryCalibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Navigating the Projector Menus Are disabledChannel Setup 17. Copying a Channel Auto Setup You cannot use Auto Setup with a locked channel. Copy18. Resize Presets No Resizing Native aspect ratio is with the primary lens only. With anInstallation Recommended see below Adjust Pixel Tracking before Pixel PhaseValues shown represent where the approximate center On an internal grayscale test pattern Input Levels are not applicable to DVI InputExperienced technicians use the Input Levels submenu There must be at least two consecutive white pixels present Uncheck this item before exiting this menuWorking With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Using the On-Screen Menus OperationInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position Information ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Number Hardware Firmware 0002.003A Date Mar 15You must enter a passcode to access the Calibration menu CalibrationOperation Service Input Names Restore Composite Video Component SDTip Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Recording the Serial Number of a New Lamp Lamp is accurateLens Replacement Removing the Primary LensSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Power down the projector Code Description General VX-40d/-50d/-60d/-80d Error CodesError Codes Power and Cooling Code Description Lamp FailuresPanel Driver and Formatter Code Description Tipm Image ProcessorBuilt-In Keypad Code Description Miscellaneous Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax CommandAspect Ratio Commands VIRTUAL235 YESImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Serial Communications VX-40d/-50d/-60d/ -80d Specifications VX-40d/-50d/-60d/-80d SpecificationsPower Requirements VX-40d/-60d Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-50d/-80dLimited Warranty DimensionsWeight without lens Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-40d/-50d/-60d/ -80d Dimensions VX-40d/-50d/-60d/-80d DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual