Runco VX-50d, VX-80d Mounting VX-40d/-50d/-60d/ -80d, Floor Mounting, Ceiling Mounting, Angle

Page 40

Installation

3.6 Mounting the

VX-40d/-50d/-60d/ -80d

There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another.

Floor Mounting

In typical front and rear screen installations, the projector can be placed on a secure and

 

level surface such as a table or cart. Carts are useful when moving a projector during a

 

presentation or from site to site. If possible, lock the wheels when it’s in position to prevent

 

it from being moved during a presentation.

Ceiling Mounting

The projector can also be inverted and suspended from the ceiling using a specially

 

designed ceiling mount fixture. This type of mounting is recommended for fixed

 

installations and for those that want the projector out of sight or have a limited space for

 

projector and audience.

 

WARNING

Use only the Runco-approved ceiling mount kit designed for your

 

projector. Carefully read and follow the installation instructions

 

 

provided with the ceiling mount kit. Failure to do so could cause

 

 

serious personal injury.

Adjusting the Projection

If the VX-40d/-50d/-60d/-80d is ceiling-mounted and the screen is significantly lower than

Angle

the projector, you can tilt the projector at an angle by adjusting the ceiling mount.

The projector can be rotated (front-to-back) up to 360 degrees and mounted without it affecting performance. However, to ensure optimal performance of the lamp, limit the side-to-side tilt of the projector to ±15 degrees; see Figure 3-7.

± 360º

± 15º

Figure 3-7. Mounting Angle Ranges (Front-to-Back and Side-to-Side)

For a floor (non-AutoScope) installation, turn the two adjustable feet on the bottom of the projector to adjust the projection angle.

If you do either of these things, you may need to make keystone adjustments or vertically shift the image using the on-screen display (OSD) controls, to compensate. For detailed instructions, refer to Using the On-Screen Menus on page 57.

28

Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual

Image 40
Contents VX-40d / VX-50d VX-60d / VX-80d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsTable of Contents List of Figures Xii About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Optional Accessories RuncoVX-40d/-50d/-60d/ -80d at a Glance VX-40d/-50d/-60d/-80d Top/Rear/Front ViewRear Foot Stationary Power Input 100 to 240 VAC VX-40d/-50d/-60d/ -80d Input PanelRS232 RS232 OUT Not used RS422 Not used Gpio Not usedInput 3 Video / Input 4 S-Video Input 2 DVIVX-40d/-50d/-60d/ -80d Rear-Panel Keypad FocusZoom VX-40d/-50d/-60d/-80d has its own internal menu systemMenu Navigation Buttons Input 1 BNCHelp ExitDHD Controller Front Panel DHD Controller Front PanelDHD Controller Rear Panel OutputsHD1 / HD2 Analog BNC connectors Component Video RCA connectorsInputs 3. DVI 1 / DVI 2 Digital Video 1 / S-VIDEORemote Control DHD ControllerOn / OFF Cursor ButtonsFor more information about aspect ratios, refer to Table VideoMemory Preset Buttons ISF NT Night Aspect Ratio Selection ButtonsANA Anamorphic 4X3 Standard 43Controls and Functions Installation Quick Setup Installation OverviewInstallation specialist Step Procedure For Details, Refer toInstallation Considerations Projector Installation OptionsInstallation Type Ambient LightVX-40d/-50d Lens Options and Throw Ratios Throw Ratio Throw Distance RangeLens Option Note Throw Dist Minimum MaximumVX-60d/-80d Lens Options and Throw Ratios Lens Option Note Throw Dist Screen Width Minimum MaximumVertical and Horizontal PositionHorizontal Lens Shift Screen center are aligned with each otherFolded Optics Installing the Projection Lens Lens Assembly Front ViewAutoScope or Base Plate Installing the Optional CineWide Lens MountFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Adjusting the Projection Mounting VX-40d/-50d/-60d/ -80dFloor Mounting Ceiling MountingConnector Panel Access Connecting the DHD Controller to VX-40d/-50d/-60d/-80dConnecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toConnecting to AC Power Input voltage to the AutoScope lens motor must be betweenYou must enter a passcode to access the Service menu Turning on the PowerSelecting the Input Source Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or BaseHorizontal Position X Adjustment Too Low Correct position Too High Wrong Position Correct Position GeometryCalibrating Projector Inputs Main TheaterMaster Remote 1. Power Button Control Functions Channel Setup Are disabledNavigating the Projector Menus 17. Copying a Channel Auto Setup You cannot use Auto Setup with a locked channel. Copy18. Resize Presets No Resizing Native aspect ratio is with the primary lens only. With anInstallation Values shown represent where the approximate center Adjust Pixel Tracking before Pixel PhaseRecommended see below Experienced technicians use the Input Levels submenu Input Levels are not applicable to DVI InputOn an internal grayscale test pattern There must be at least two consecutive white pixels present Uncheck this item before exiting this menuWorking With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Installation Using the On-Screen Menus OperationISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.003A Date Mar 15You must enter a passcode to access the Calibration menu CalibrationOperation Service Input Names Restore Composite Video Component SDTip HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionAuto Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Recording the Serial Number of a New Lamp Lamp is accurateLens Replacement Removing the Primary LensTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Power down the projector Error Codes VX-40d/-50d/-60d/-80d Error CodesCode Description General Power and Cooling Code Description Lamp FailuresBuilt-In Keypad Code Description Tipm Image ProcessorPanel Driver and Formatter Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands CommandAspect Ratio Commands VIRTUAL235 YESImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Serial Communications VX-40d/-50d/-60d/ -80d Specifications VX-40d/-50d/-60d/-80d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements VX-40d/-60d VX-50d/-80dDimensions Weight without lensLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-40d/-50d/-60d/ -80d Dimensions VX-40d/-50d/-60d/-80d DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual