Runco VX-6000D manual RS-232 Controller, Connection

Page 48

Installation

RS-232 Controller

➤

Use a standard, 9-pin RS-232 cable to connect a PC or home theater control/automation

Connection

 

system (if present) to the RS-232 Control port on the DHD Controller; see Figure 3-13.

 

 

For more information about using this connection, refer to Serial Communications on

 

 

page 79.

 

 

 

 

 

 

5

4

3

2

1

 

 

 

TRIGGERS

 

 

 

 

1

2

3

IR

Pb

Pr

Y

S-Video 1

 

 

 

Component Video

Video

S-Video 2

RS-232 Out

RS-232 Control

9 8 7 6

2 Transmit Data

3 Receive Data

5 Ground

(none of the other pins are used)

to Automation/ Control System or PC

Figure 3-13. RS-232 Control System Connection

36

Runco VX-6000d Owner’s Operating Manual

Page 47 Page 49
Image 48
Page 47 Page 49
Contents VX-6000d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Ceiling Mounting Inverted Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsTable of Contents List of Figures VX-6000d About This Manual Using This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories VX-6000d at a Glance VX-6000d Front/Top/Side/Bottom/Rear ViewVertical Lens Shift RS-232C Input RJ-11 female connector VX-6000d Rear PanelDHD Controller Front Panel DHD Controller Front PanelEnter Button Component Video RCA connectors DHD Controller Rear PanelOutputs 1. Hdmi OUT Inputs 2. Hdmi 1 / Hdmi 2 DigitalVideo 1 / S-VIDEO Volt 750 mA Trigger OutputsComLink RS-232 Output VX-6000d Remote Control UnitsStandard DHD Remote ControlOn / OFF Cursor ButtonsVideo Comp ComponentMemory Preset Buttons ISF NT Night Aspect Ratio Selection ButtonsANA Anamorphic 4X3 Standard 43Volume +/- / Mute / OK / CH + Touch-Screen RemoteComp VID 1 / S-VIDHD 1 / HD Hdmi 1 / HdmiEnter / Cursor Buttons Focus / Focus +Zoom / Zoom + Only trained service personnel should use the built-in VX-6000d Built-In KeypadNot used Installation OperationOther surfaces Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Projector Installation OptionsInstallation Type ConsiderationsVX-6000d Lens Options and Throw Ratios Throw DistanceVertical and Horizontal PositionHorizontal Lens Shift Example Only Vertical and Horizontal Lens Shift Limits Installing the Optional CineWide Lens Mount Folded Optics Other ConsiderationsInstallation Install Ceiling Mount Extension BracketsCineWide with Mounting VX-6000dConnections to VX-6000d and DHDConnecting the VX-6000d to the DHD Controller Connecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsRS-232 Controller ConnectionConnecting 12-Volt Trigger Outputs toExternal Theater EquipmentConnecting an External IR Turning on the Power Connecting to AC PowerAdjusting the Picture Orientation Primary Lens Adjustments17. Vertical and Horizontal Lens Shift Adjustments Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Configure Lens Motor Adjust the AnamorphicAdjusting the Horizontal X Lens Position Trigger CineWide withToo Low Correct position Too High Adjusting the Geometry Anamorphic Lens Top ViewInstallation Runco VX-6000d Owner’s Operating Manual Installation Operation ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Num Hardware Firmware 0002.001A Date Oct 9You must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Service Tip ADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto On-Screen Menus for 1080i Digital or 1080p Signals Picture Adjust AdvancedWhite Balance HD/RGB AdjVX-6000d Main Menu 1080i Digital or 1080p Sources Only Picture Adjust Default Settings for Selected Picture MemoryLanguage Picture Adjust Advanced Menu. This sub-menu presents the following optionsEffects of Primary Color Hue Adjustments White Balance HD/RGB AdjOverscan 480i/480p signals only Refer to Overscan on Lamp Hours read-onlyRefer to Lamp Hours onOptions Orientation Refer to Adjusting the Picture Orientation on Always set this option to On. Doing otherwise may disruptRunco Technical Support Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Display Device on Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands CommandAspect Ratio Commands VIRTUAL235 YESBrightness Iheight Bkgnd Command Parameter min/max Value Stored? Description Enter keyVX-6000d Specifications VX-6000d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-6000d Dimensions VX-6000d DimensionsPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 112 pages 43.78 Kb
Top Page Image Contents