Runco VX-6000D manual Lens Replacement, Only trained, authorized Runco dealers should attempt to

Page 86

Maintenance and Troubleshooting

5.2

Lens Replacement

Figure 5-1shows the VX-6000d lens assembly.

Motor Assembly

9/64” Hex Screw (6x) for Mounting Lens

	Motor Assembly
	Electrical Connector
Front of Lens	and Harness
Projector Front Jewelry

Figure 5-1. VX-6000d Lens Assembly Exploded View

Only trained, authorized Runco dealers should attempt to

Note remove or replace a lens. Please read this procedure carefully before doing so.

Lens replacement is normally performed at the Runco factory. Field replacement of lenses is generally only required if the projector is re-installed in a new location or the lens has been damaged.

1.Remove the Projector Front Jewelry by loosening the captive #2 Phillips screw below the lens.

74	Runco VX-6000d Owner’s Operating Manual

Image 86

Contents VX-6000d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Ceiling Mounting Inverted Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents List of Figures VX-6000d About This Manual Using This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories VX-6000d at a Glance VX-6000d Front/Top/Side/Bottom/Rear ViewVertical Lens Shift RS-232C Input RJ-11 female connector VX-6000d Rear PanelDHD Controller Front Panel DHD Controller Front PanelEnter Button Outputs 1. Hdmi OUT Component Video RCA connectorsDHD Controller Rear Panel Inputs 2. Hdmi 1 / Hdmi 2 DigitalComLink RS-232 Output Video 1 / S-VIDEOVolt 750 mA Trigger Outputs Standard DHD Remote VX-6000d RemoteControl Units ControlVideo On / OFFCursor Buttons Comp ComponentANA Anamorphic Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons 4X3 Standard 43Volume +/- / Mute / OK / CH + Touch-Screen RemoteHD 1 / HD CompVID 1 / S-VID Hdmi 1 / HdmiZoom / Zoom + Enter / Cursor ButtonsFocus / Focus + Not used Only trained service personnel should use the built-inVX-6000d Built-In Keypad Installation OperationOther surfaces Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type InstallationProjector Installation Options ConsiderationsVX-6000d Lens Options and Throw Ratios Throw DistanceVertical and Horizontal PositionHorizontal Lens Shift Example Only Vertical and Horizontal Lens Shift Limits Installing the Optional CineWide Lens Mount Folded Optics Other ConsiderationsInstallation CineWide with Install Ceiling MountExtension Brackets Connections to MountingVX-6000d VX-6000d and DHDConnecting the VX-6000d to the DHD Controller Connecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsRS-232 Controller ConnectionExternal Theater Connecting 12-VoltTrigger Outputs to EquipmentConnecting an External IR Turning on the Power Connecting to AC PowerAdjusting the Picture Orientation Primary Lens Adjustments17. Vertical and Horizontal Lens Shift Adjustments Lens ShiftCarriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens MotorAdjust the Anamorphic Trigger CineWide withToo Low Correct position Too High Adjusting the Geometry Anamorphic Lens Top ViewInstallation Runco VX-6000d Owner’s Operating Manual Installation Operation Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Num Hardware Firmware 0002.001A Date Oct 9You must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Service Tip Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV On-Screen Menus for 1080i Digital or 1080p Signals White Balance Picture AdjustAdvanced HD/RGB AdjVX-6000d Main Menu 1080i Digital or 1080p Sources Only Language Picture AdjustDefault Settings for Selected Picture Memory Picture Adjust Advanced Menu. This sub-menu presents the following optionsEffects of Primary Color Hue Adjustments White Balance HD/RGB AdjOptions Overscan 480i/480p signals only Refer to Overscan onLamp Hours read-onlyRefer to Lamp Hours on Runco Technical Support Orientation Refer to Adjusting the Picture Orientation onAlways set this option to On. Doing otherwise may disrupt Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Display Device on Maintenance and Troubleshooting Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax CommandAspect Ratio Commands VIRTUAL235 YESBrightness Iheight Bkgnd Command Parameter min/max Value Stored? Description Enter keyVX-6000d Specifications VX-6000d SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-6000d Dimensions VX-6000d DimensionsPage Runco CL-810 Owner’s Operating Manual

Related manuals

Manual 112 pages 43.78 Kb