Runco VX-6000D manual Anamorphic Lens Top View, Adjusting the Geometry

Page 58

Installation

Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely from side to side. Then, angle the lens to even out any left-right pincushion distortion:

Anamorphic Lens (Top View)

Wrong Position

Correct Position

Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to secure the lens in place.

Adjusting the Geometry:

1.Input an anamorphic cross-hatch test pattern to the projector.

2.Loosen the three Lens Rotation Set Screws (shown in Figure 3-19)on the lens adapter ring just enough to allow it to rotate freely.

3.Grasp the lens by the front ring and rotate the lens until the image is properly anamorphic:

Wrong Position

Correct Position

4.When the image geometry appears correct, tighten the three Lens Rotation Set Screws to secure the lens in place. (When viewed from the front, the rear opening on the anamorphic lens should appear as a tall, narrow oval.)

46	Runco VX-6000d Owner’s Operating Manual

Image 58

Contents VX-6000d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Ceiling Mounting Inverted Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents List of Figures VX-6000d About This Manual Using This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories VX-6000d at a Glance VX-6000d Front/Top/Side/Bottom/Rear ViewVertical Lens Shift RS-232C Input RJ-11 female connector VX-6000d Rear PanelDHD Controller Front Panel DHD Controller Front PanelEnter Button Outputs 1. Hdmi OUT Component Video RCA connectorsDHD Controller Rear Panel Inputs 2. Hdmi 1 / Hdmi 2 DigitalVolt 750 mA Trigger Outputs Video 1 / S-VIDEOComLink RS-232 Output Standard DHD Remote VX-6000d RemoteControl Units ControlVideo On / OFFCursor Buttons Comp ComponentANA Anamorphic Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons 4X3 Standard 43Volume +/- / Mute / OK / CH + Touch-Screen RemoteHD 1 / HD CompVID 1 / S-VID Hdmi 1 / HdmiFocus / Focus + Enter / Cursor ButtonsZoom / Zoom + VX-6000d Built-In Keypad Only trained service personnel should use the built-inNot used Installation OperationOther surfaces Installation Overview Quick SetupStep Procedure For Details, Refer to Installation Type InstallationProjector Installation Options ConsiderationsVX-6000d Lens Options and Throw Ratios Throw DistanceVertical and Horizontal PositionHorizontal Lens Shift Example Only Vertical and Horizontal Lens Shift Limits Installing the Optional CineWide Lens Mount Folded Optics Other ConsiderationsInstallation Extension Brackets Install Ceiling MountCineWide with Connections to MountingVX-6000d VX-6000d and DHDConnecting the VX-6000d to the DHD Controller Connecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsRS-232 Controller ConnectionExternal Theater Connecting 12-VoltTrigger Outputs to EquipmentConnecting an External IR Turning on the Power Connecting to AC PowerAdjusting the Picture Orientation Primary Lens Adjustments17. Vertical and Horizontal Lens Shift Adjustments Lens ShiftCarriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens MotorAdjust the Anamorphic Trigger CineWide withToo Low Correct position Too High Adjusting the Geometry Anamorphic Lens Top ViewInstallation Runco VX-6000d Owner’s Operating Manual Installation Operation Input Source ISF PresetsService Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Num Hardware Firmware 0002.001A Date Oct 9You must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Service Tip HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionAuto On-Screen Menus for 1080i Digital or 1080p Signals White Balance Picture AdjustAdvanced HD/RGB AdjVX-6000d Main Menu 1080i Digital or 1080p Sources Only Default Settings for Selected Picture Memory Picture AdjustLanguage Picture Adjust Advanced Menu. This sub-menu presents the following optionsEffects of Primary Color Hue Adjustments White Balance HD/RGB AdjLamp Hours read-onlyRefer to Lamp Hours on Overscan 480i/480p signals only Refer to Overscan onOptions Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation onRunco Technical Support Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Display Device on Maintenance and Troubleshooting Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax CommandAspect Ratio Commands VIRTUAL235 YESBrightness Iheight Bkgnd Command Parameter min/max Value Stored? Description Enter keyVX-6000d Specifications VX-6000d SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-6000d Dimensions VX-6000d DimensionsPage Runco CL-810 Owner’s Operating Manual

Related manuals

Manual 112 pages 43.78 Kb