Runco VX-6000D manual Gray Yellow Cyan Green Magenta Red Blue

Page 68

Operation

Select Color and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

gray

yellow

cyan

green

magenta

red

blue

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint and press ENTER. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

Like the brightness and contrast controls, the color and tint controls

Note are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

56

Runco VX-6000d Owner’s Operating Manual

Image 68
Contents VX-6000d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Ceiling Mounting Inverted Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsTable of Contents List of Figures VX-6000d About This Manual Using This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories VX-6000d at a Glance VX-6000d Front/Top/Side/Bottom/Rear ViewVertical Lens Shift RS-232C Input RJ-11 female connector VX-6000d Rear PanelDHD Controller Front Panel DHD Controller Front PanelEnter Button Component Video RCA connectors DHD Controller Rear PanelOutputs 1. Hdmi OUT Inputs 2. Hdmi 1 / Hdmi 2 DigitalComLink RS-232 Output Video 1 / S-VIDEOVolt 750 mA Trigger Outputs VX-6000d Remote Control UnitsStandard DHD Remote ControlOn / OFF Cursor ButtonsVideo Comp ComponentMemory Preset Buttons ISF NT Night Aspect Ratio Selection ButtonsANA Anamorphic 4X3 Standard 43Volume +/- / Mute / OK / CH + Touch-Screen RemoteComp VID 1 / S-VIDHD 1 / HD Hdmi 1 / HdmiZoom / Zoom + Enter / Cursor ButtonsFocus / Focus + Not used Only trained service personnel should use the built-inVX-6000d Built-In Keypad Installation OperationOther surfaces Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Projector Installation OptionsInstallation Type ConsiderationsVX-6000d Lens Options and Throw Ratios Throw DistanceVertical and Horizontal PositionHorizontal Lens Shift Example Only Vertical and Horizontal Lens Shift Limits Installing the Optional CineWide Lens Mount Folded Optics Other ConsiderationsInstallation CineWide with Install Ceiling MountExtension Brackets Mounting VX-6000dConnections to VX-6000d and DHDConnecting the VX-6000d to the DHD Controller Connecting Source Digital DTV RGB or Component Video Connections See Figure 10. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure 11. Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 12. Composite, S-Video and Component Video ConnectionsRS-232 Controller ConnectionConnecting 12-Volt Trigger Outputs toExternal Theater EquipmentConnecting an External IR Turning on the Power Connecting to AC PowerAdjusting the Picture Orientation Primary Lens Adjustments17. Vertical and Horizontal Lens Shift Adjustments Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Configure Lens Motor Adjust the AnamorphicAdjusting the Horizontal X Lens Position Trigger CineWide withToo Low Correct position Too High Adjusting the Geometry Anamorphic Lens Top ViewInstallation Runco VX-6000d Owner’s Operating Manual Installation Operation ISF Presets ServiceInput Source Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Num Hardware Firmware 0002.001A Date Oct 9You must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Service Tip Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV On-Screen Menus for 1080i Digital or 1080p Signals Picture Adjust AdvancedWhite Balance HD/RGB AdjVX-6000d Main Menu 1080i Digital or 1080p Sources Only Language Picture AdjustDefault Settings for Selected Picture Memory Picture Adjust Advanced Menu. This sub-menu presents the following optionsEffects of Primary Color Hue Adjustments White Balance HD/RGB AdjOptions Overscan 480i/480p signals only Refer to Overscan onLamp Hours read-onlyRefer to Lamp Hours on Runco Technical Support Orientation Refer to Adjusting the Picture Orientation onAlways set this option to On. Doing otherwise may disrupt Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Display Device on Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands CommandAspect Ratio Commands VIRTUAL235 YESBrightness Iheight Bkgnd Command Parameter min/max Value Stored? Description Enter keyVX-6000d Specifications VX-6000d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-6000d Dimensions VX-6000d DimensionsPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 112 pages 43.78 Kb