Sharp PG-D100U operation manual Select input, Adjust the volume, Video, On-Screen Display

Page 22

VIDEO

On-Screen Display

VIDEO

• N T S C

For viewing the picture from a video source connected to: VIDEO INPUT or

S-VIDEO INPUT

7. Select input

Press the INPUT SELECT button to switch the picture input. When you press the button, the current input mode is displayed for about 4 seconds. If you press the button again while the input mode is displayed, the mode changes as shown on the left.

Confirm the selected input terminal and press the INPUT SELECT button.

Notes:

RGB COMPUTER RGB

1024×768

6 0 H z

• This can be selected directly using the VIDEO and DATA

buttons on the remote control.

• In VIDEO mode, the system being received will be indicated

below the “VIDEO” display.

• When selecting RGB mode, the resolution being displayed will

be indicated under “RGB,” as shown on the left. (Refer to the

second example when connecting to Mac display.)

RGB

1024×768

6 0 H z

Mac RGB

640×480

35 KHz

RGB

800×600

6 0 H z

RGB

640×480

34.97 KHz

RGB

832×624

• When no signals are being received, “NO SIGNAL” will be

displayed. When receiving a signal the projector is not preset

to receive, “NOT REG.” will be displayed. (This display

function does not operate in Video mode.)

8. Adjust the volume

The number of displayed segments (0~60) increases or decreases as the volume is raised or lowered.

V O L U M E

3 8

Press the VOLUME UP-DOWN buttons on the projector or on the remote control to adjust the volume.

MUTE

•Press the MUTE button to temporarily turn off the sound.

•Press the MUTE button once again to turn the sound back on.

POWER

LAMP

TEMP.

9.To turn off the power from the projector or remote control

The power can be temporarily turned off by pressing the POWER ON/OFF button on either the projector or remote control.

The POWER indicator will turn red and the cooling fan will run for 90 seconds, then the power will turn off, and the projector will return to STANDBY mode.

The power can be turned on again either from the projector or remote control. When the power is turned on, the POWER indicator and LAMP REPLACEMENT indicator light green.

Note:

•When the MAIN POWER is off on the projector set, the power cannot be turned on from the remote control.

E-22

Image 22

Contents Model No. PG-D100U Dear SHARP CustomerImportant Information Serial NoIMPORTANT SAFEGUARDS INFORMATIONAbout the Temperature Monitor Function About the Lamp Monitor FunctionVERSATILE REMOTE CONTROL Outstanding FeaturesCautions Concerning the Laser Pointer DIRECT COMPUTER COMPATIBILITYFRONT VIEW Location of ControlsMain Power switch OPERATION PANEL ON TOP OF PROJECTORRemote control handling precautions Operating the Wireless Mouse Remote ControlWireless Mouse Remote Control FRONT VIEWREAR VIEW Using the optional cable with the remote controlTOP VIEW Transmission rangeFunctions and Operations Wireless Mouse FunctionsConnection Example MOUSE buttons2. Turn on the POWER Setting Up the Projector1. Turn on the MAIN POWER 3. Adjusting the FocusDistance from screen Projector Distance and Picture Size RelationshipHeight of projector 1. Press the MENU button Using the Image Invert/Reverse FunctionCaution When setting up the projector 2. Reversed Image ModeExample of a ceiling-mount setup Example of a standard setup TOP VIEWExample of a reversed image setup SIDE VIEW3. Make any minor adjustments necessary 1. Press the adjuster release and lift the2. Remove your hand from the adjuster release Use the carrying handle when carrying the projectorConnecting the Projector Input terminalsConnecting the Projector RGB Computer 640 ⋅ 480 resolution Connecting to the Computer RGB Input/Output Terminals2. Connecting to a Macintosh Series Computer 832 ⋅ 624 resolution4. Connecting to the COMPUTER RGB AUDIO INPUT 3. Connecting to other compatible computers5. Connecting an external monitor For IBM and compatibles Input Signals Recommended TimingFor Apple Macintosh Series ADJUSTMENT / buttons. Adjust the item with the ADJUSTMENT / buttons RGB Adjustment Controls2. Select the item you wish to adjust with the Description of Adjustment Items3. Turn on the POWER Basic Operation of the Projector2. Turn on the MAIN POWER 1. Connect the AC cord6. Change the system mode Setting the ON-SCREEN DISPLAY language5. Select one of eight ON-SCREEN DISPLAY languages On-Screen Display7. Select input 8. Adjust the volume9. To turn off the power from the projector or remote control VIDEO2. Adjust the Picture Adjusting the Picture1. Use the MENU button to select the mode to be adjusted 3. Display Only the Item to Adjust2. Press the ADJUSTMENT / buttons Computer Mode Memory Adjustments1. Press the ENTER button to select the Memory Adjustment mode 3. Press the MENU button anytime to exit RGB ADJAdjusting the Audio 2. Press the E-ZOOM button on the remote E-ZOOM Function1. Press the MENU button to select E-ZOOM mode controlSelecting the Remote Mouse Functions on the ProjectorChecking the system Checking the Lamp Usage TimeUsing the Black Screen Function BLACK SCREENOn-screen Display Using the Blue Screen FunctionUsing the On-Screen Display Override Function REMAIN 5M REMAIN 4M REMAIN 1M4 Clean the AIR FILTER Air Filter Maintenance1 the MAIN POWER Turn OFFMaintenance Indicators Lamp/Maintenance IndicatorsBefore Calling for Service LampIMPORTANT NOTE TO U.S. CUSTOMERS Lamp ReplacementHow to Change the Lamp Removing the lamp unit see figureInstalling the lamp unit Resetting the lamp timerConnection Pin Assignments 1. PC control RS-232C Terminal Specifications4. Commands 2. Communication conditionsSwitch to video screen Set to PAL mode For the RGB/VIDEO setting, select video and set the PAL modeWhen BRIGHT of VIDEO IMAGE ADJUSTMENT is set to ExamplesSpecifications Specifications are subject to change without noticeSide View DimensionsTop View Bottom View