Sharp PG-D100U E-ZOOM Function, Press the MENU button to select E-ZOOM mode, control

Page 26

E-ZOOM Function

E-ZOOM Function

E-ZOOM Function

■This projector has an E-ZOOM (640 ⋅ 480 dot, etc.) mode which enlarges the display when inputting an image of less than 800 ⋅ 600 dot in resolution. In the XGA (1024 ⋅ 768 dot) mode, compression enables full-mode display.

1

On-Screen Display


	I M A G E	A D J .
			[ O F F ]
	B L A C K S C R E E N		[ O F F ]
	I N P U T D I S P L A Y		[ O F F ]
	E - Z O O M		[ O N ]
	R E V E R S E		[ O F F ]
	I N V E R T		[ O F F ]
	: S E L .
	: A D J .	MENU : E N D

1.Press the MENU button to select E-ZOOM mode.

Press the MENU button. While the MENU screen is displayed, press the ADJUSTMENT / buttons to select IMAGE ADJ. Then press the ENTER button to display the IMAGE ADJ. screen as shown. Press the ADJUSTMENT

/buttons to select E-ZOOM, and press the ADJUST- MENT / buttons to select ON. When the VGA (640 ⋅ 480 dot) is input, the projector will enter E-ZOOM mode.

E-ZOOM (ON): The screen image will be enlarged to 800 ⋅ 600 dot.

E-ZOOM (OFF): The resolution of the image does not change.

E-ZOOM (---): No input

Notes:

•Select ON 1 or ON 2 to set the status for either a 640 ⋅ 400 dot image or 640 ⋅ 350 dot image in the E-ZOOM mode.

•In the E-ZOOM mode, an enlarged display increases the amount of data processed on the screen and a compressed image decreases the number of lines displayed, which may make characters difficult to read.

2

2. Press the E-ZOOM button on the remote

control.

The E-ZOOM button on the remote control can be used to

select E-ZOOM and NO E-ZOOM modes.

Note:

• In SVGA (800 ⋅ 600 dots) or Mac 16" (832 ⋅ 624 dots) mode,

E-ZOOM (ON)		E-ZOOM (OFF)	(---) appears, indicating the E-ZOOM function does not
			operate in this mode.

3. Press the MENU button anytime to exit E-ZOOM mode.

Notes:

• E-ZOOM function does not operate in SVGA (800 ⋅ 600), Mac 16" (832 ⋅ 624), NTSC, PAL, or SECAM INPUT modes.

• When connecting to some Mac 16" notebook computers, 832 ⋅ 624 dot signals may be output even in 640 ⋅ 480 mode, thus disabling the E-ZOOM function.

• When connecting to some SVGA notebook computers, 800 ⋅ 600 dot signals may be output even in 640 ⋅ 480 mode, thus disabling the E-ZOOM function.

E-26

Image 26

Contents Model No. PG-D100U Dear SHARP CustomerImportant Information Serial NoIMPORTANT SAFEGUARDS INFORMATIONAbout the Temperature Monitor Function About the Lamp Monitor FunctionVERSATILE REMOTE CONTROL Outstanding FeaturesCautions Concerning the Laser Pointer DIRECT COMPUTER COMPATIBILITYFRONT VIEW Location of ControlsMain Power switch OPERATION PANEL ON TOP OF PROJECTORRemote control handling precautions Operating the Wireless Mouse Remote ControlWireless Mouse Remote Control FRONT VIEWREAR VIEW Using the optional cable with the remote controlTOP VIEW Transmission rangeFunctions and Operations Wireless Mouse FunctionsConnection Example MOUSE buttons2. Turn on the POWER Setting Up the Projector1. Turn on the MAIN POWER 3. Adjusting the FocusHeight of projector Projector Distance and Picture Size RelationshipDistance from screen 1. Press the MENU button Using the Image Invert/Reverse FunctionCaution When setting up the projector 2. Reversed Image ModeExample of a ceiling-mount setup Example of a standard setup TOP VIEWExample of a reversed image setup SIDE VIEW3. Make any minor adjustments necessary 1. Press the adjuster release and lift the2. Remove your hand from the adjuster release Use the carrying handle when carrying the projectorConnecting the Projector Input terminalsConnecting the Projector RGB Computer 640 ⋅ 480 resolution Connecting to the Computer RGB Input/Output Terminals2. Connecting to a Macintosh Series Computer 832 ⋅ 624 resolution5. Connecting an external monitor 3. Connecting to other compatible computers4. Connecting to the COMPUTER RGB AUDIO INPUT For Apple Macintosh Series Input Signals Recommended TimingFor IBM and compatibles ADJUSTMENT / buttons. Adjust the item with the ADJUSTMENT / buttons RGB Adjustment Controls2. Select the item you wish to adjust with the Description of Adjustment Items3. Turn on the POWER Basic Operation of the Projector2. Turn on the MAIN POWER 1. Connect the AC cord6. Change the system mode Setting the ON-SCREEN DISPLAY language5. Select one of eight ON-SCREEN DISPLAY languages On-Screen Display7. Select input 8. Adjust the volume9. To turn off the power from the projector or remote control VIDEO2. Adjust the Picture Adjusting the Picture1. Use the MENU button to select the mode to be adjusted 3. Display Only the Item to Adjust2. Press the ADJUSTMENT / buttons Computer Mode Memory Adjustments1. Press the ENTER button to select the Memory Adjustment mode 3. Press the MENU button anytime to exit RGB ADJAdjusting the Audio 2. Press the E-ZOOM button on the remote E-ZOOM Function1. Press the MENU button to select E-ZOOM mode controlSelecting the Remote Mouse Functions on the ProjectorChecking the system Checking the Lamp Usage TimeUsing the Black Screen Function BLACK SCREENOn-screen Display Using the Blue Screen FunctionUsing the On-Screen Display Override Function REMAIN 5M REMAIN 4M REMAIN 1M4 Clean the AIR FILTER Air Filter Maintenance1 the MAIN POWER Turn OFFMaintenance Indicators Lamp/Maintenance IndicatorsBefore Calling for Service LampIMPORTANT NOTE TO U.S. CUSTOMERS Lamp ReplacementHow to Change the Lamp Removing the lamp unit see figureInstalling the lamp unit Resetting the lamp timerConnection Pin Assignments 1. PC control RS-232C Terminal Specifications4. Commands 2. Communication conditionsSwitch to video screen Set to PAL mode For the RGB/VIDEO setting, select video and set the PAL modeWhen BRIGHT of VIDEO IMAGE ADJUSTMENT is set to ExamplesSpecifications Specifications are subject to change without noticeSide View DimensionsTop View Bottom View