AMX Precis SD instruction manual Change the enclosure’s settings instead, use XNConnect see

Page 27

Installation & Setup

2.Plug one end of the null modem serial cable into the CONTROL port on the enclosure (FIG. 9).

FIG. 9 Attach null modem serial cable to CONTROL port

3.Plug the other end of the serial cable into the serial port on the serial controller/device.

4.Open the serial communication software on the PC and set the PC’s

port settings to match the Precis SD default settings (see table to the

Precis SD

 

CONTROL Port Settings

right). In addition to the default baud rate of 9600, Precis SD

 

 

 

enclosures support baud rates of 19200, 38400, and 57600. The

Baud Rate

 

9600

settings on the PC serial communication software and the enclosure

Data Bits

 

8

must correspond to each other. If a change is required to make them

Parity

 

None

match, changing the PC’s settings is preferable. If you decide to

 

 

 

Stop Bits

 

1

change the enclosure’s settings instead, use XNConnect (see the

 

 

 

Flow Control

 

None

Help file).

 

 

 

 

 

 

Caution: To avoid system damage, follow the power-up sequence on page 27. We recommend attaching all power cords to a surge protector and/or AC line conditioner.

5.If not already on, apply power first to the Precis SD enclosure and then to the source and destination devices (see “Applying Power & Startup” on page 27).

6.Set up and run the desired method of control:

AMX control devices – For specific control programming information, contact your AMX representative.

APControl 3.0 – Install and open the program from the AMX AutoPatch CD (if your AMX account has the required permissions, the program can be downloaded from www.amx.com). Follow the setup wizard and open the APControl Launchbar.

Terminal emulation (e.g., HyperTerminal) – Open the program, select the COM port, and check that the settings match those in the Precis SD CONTROL Port Settings table (see above).

Click OK.

A short splash screen appears.

7.Execute a test switch to ensure the Precis SD is working properly (see “Executing a Test Switch” on page 29).

22

Precis SD Instruction Manual

Image 27
Contents Precis SD AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Contents Appendix a Managing Configuration Files ESD Warning Important Safety Information & Instructions Information et directives de sécurité importantes Copyright Notice Liability NoticeUsfcc Notice Trademark Notices Lithium Batteries NoticePage Product Notes Overview & General SpecificationsPrecis SD Features Applicability NoticeFront View Precis SD Control FeaturesRear View Rear View ComponentsCPU/Control Hardware Power Receptacle & Specifications Input & Output ConnectorsSystem Serial Number General Specifications Precis SD General SpecificationsAMX Control Software Configuration Information & Control OptionsFront Control Panel AMX Control DevicesBCS Serial Control Protocol Third-Party Controllers Overview & General Specifications Installation & Setup General Hazard PrecautionsSite Recommendations Unpacking Tips UnpackingCircuit Overloading Reliable Earthing GroundingInstallation Recommendations Rack Installation & System SetupRequired items for rack installation Optional items for rack installationTo install and set up a Precis SD system in a rack Installation ProcedureAdditional Installation Options Attaching External Controllers PC Requirements for BCS RS-232 Pin DiagramAttaching Serial Controllers PC Requirements for APControlChange the enclosure’s settings instead, use XNConnect see Attaching External XNNet Controllers Communication Cable RequirementsTo establish a Remote port connection with an XNNet device Attaching Inputs & Outputs Signal Types & ConnectorsTo connect video inputs and outputs Cabling Video ConnectorsTo attach stereo audio input and output wires Wiring Audio ConnectorsWiring Sources & Destinations Attaching WiresPower-Up Sequence To apply power Applying Power & StartupHyperTerminal Serial Control Device StartupAPControl APWebExecuting a Test Switch Executing a Test SwitchAPControl 3.0 or APWeb To execute a test switch using the control panelControl Panel AMX Control DeviceTroubleshooting BCS CommandsTo disconnect the factory default switch using BCS commands To execute a test switch using BCS commandsAMX Contact Information Technical SupportSignal Specifications Ultra-Wideband 500 MHz SpecificationsSync Specifications Standard Audio Signal Specifications Standard Audio SpecificationsOverview Precis SD Control Panel OperationVirtual Matrices Levels Audio Adjust Keys optionalControl Keys Modes of OperationTo execute a switch selecting input source first Executing & Disconnecting SwitchesSwitching Level Executing a SwitchTo execute a switch selecting output destination first Disconnecting OutputsTo disconnect an output To verify the status of a signal Verifying Signal StatusExecuting Macros Local Presets Adjusting Audio Adjusting Output VolumeTo adjust output volume Purpose & Uses of Input Gain Adjusting Digital Input GainTo adjust digital input gain to equalize input levels To adjust digital input gainLocking & Unlocking the Control Panel To lock the control panelTo unlock the control panel Precis SD Control Panel Operation Applicability Notice Appendix a Managing Configuration FilesTo launch XNConnect Installing & Launching XNConnectTo install XNConnect from the AMX AutoPatch CD System RequirementsTo discover a system Discovering a SystemTo open an .xcl file Opening an .xcl Configuration FileNavigating the Interface Hardware ViewVirtual Matrix View Modifying an .xcl Configuration File Modifying Source & Destination Channel NamesTo customize the channel names To set the control panel password Setting the Control Panel PasswordTo create a new local preset Creating Local Presets MacrosAppendix a Managing Configuration Files Device Discovery Support Loading an .xcl Configuration FileSystem Component Information Appendix B Programmer’s Interface for System DiagnosticsExample Using BCS to Access System Diagnostic InformationDisplay for v1i1 verbosity 1, component Splash Screen ExamplesDisplay for v3i5 verbosity 3, component It’s Your World Take Control