AMX Precis SD instruction manual Cabling Video Connectors, To connect video inputs and outputs

Page 30

Installation & Setup

Cabling Video Connectors

The video connectors are color coded; the white BNC connectors are inputs and the black BNC connectors are outputs.

Tip: Using lacer bars or some other type of cable management system lessens the strain from cable weight on the connectors and makes servicing the enclosures easier.

For RGBHV signals, you need to attach corresponding input and output connectors on five connectors to route the entire signal. FIG. 12 shows the 5 BNC cable connectors attached for routing the R, G, B, H, and V signals through Output 8.

R

G

B

H

V

FIG. 12 Five BNC connectors are required for RGBHV signal

To connect video inputs and outputs:

1.Fasten the cable connectors onto the input and output BNC connectors.

For ultra-wideband video and sync specifications, see “Signal Specifications” on page 33.

Precis SD Instruction Manual

25

 

 

Image 30
Contents Precis SD AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Contents Appendix a Managing Configuration Files ESD Warning Important Safety Information & Instructions Information et directives de sécurité importantes Copyright Notice Liability NoticeUsfcc Notice Lithium Batteries Notice Trademark NoticesPage Applicability Notice Overview & General SpecificationsPrecis SD Features Product NotesPrecis SD Control Features Front ViewRear View Rear View ComponentsCPU/Control Hardware Power Receptacle & Specifications Input & Output ConnectorsSystem Serial Number Precis SD General Specifications General SpecificationsAMX Control Devices Configuration Information & Control OptionsFront Control Panel AMX Control SoftwareBCS Serial Control Protocol Third-Party Controllers Overview & General Specifications Installation & Setup General Hazard PrecautionsSite Recommendations Reliable Earthing Grounding UnpackingCircuit Overloading Unpacking TipsOptional items for rack installation Rack Installation & System SetupRequired items for rack installation Installation RecommendationsInstallation Procedure To install and set up a Precis SD system in a rackAdditional Installation Options Attaching External Controllers PC Requirements for APControl RS-232 Pin DiagramAttaching Serial Controllers PC Requirements for BCSChange the enclosure’s settings instead, use XNConnect see Attaching External XNNet Controllers Communication Cable RequirementsTo establish a Remote port connection with an XNNet device Signal Types & Connectors Attaching Inputs & OutputsCabling Video Connectors To connect video inputs and outputsAttaching Wires Wiring Audio ConnectorsWiring Sources & Destinations To attach stereo audio input and output wiresApplying Power & Startup Power-Up Sequence To apply powerAPWeb Serial Control Device StartupAPControl HyperTerminalExecuting a Test Switch Executing a Test SwitchAMX Control Device To execute a test switch using the control panelControl Panel APControl 3.0 or APWebTo execute a test switch using BCS commands BCS CommandsTo disconnect the factory default switch using BCS commands TroubleshootingTechnical Support AMX Contact InformationSignal Specifications Ultra-Wideband 500 MHz SpecificationsSync Specifications Standard Audio Specifications Standard Audio Signal SpecificationsPrecis SD Control Panel Operation OverviewModes of Operation Audio Adjust Keys optionalControl Keys Virtual Matrices LevelsExecuting a Switch Executing & Disconnecting SwitchesSwitching Level To execute a switch selecting input source firstTo execute a switch selecting output destination first Disconnecting OutputsTo disconnect an output Verifying Signal Status To verify the status of a signalExecuting Macros Local Presets Adjusting Audio Adjusting Output VolumeTo adjust output volume To adjust digital input gain Adjusting Digital Input GainTo adjust digital input gain to equalize input levels Purpose & Uses of Input GainLocking & Unlocking the Control Panel To lock the control panelTo unlock the control panel Precis SD Control Panel Operation Appendix a Managing Configuration Files Applicability NoticeSystem Requirements Installing & Launching XNConnectTo install XNConnect from the AMX AutoPatch CD To launch XNConnectDiscovering a System To discover a systemOpening an .xcl Configuration File To open an .xcl fileNavigating the Interface Hardware ViewVirtual Matrix View Modifying an .xcl Configuration File Modifying Source & Destination Channel NamesTo customize the channel names Setting the Control Panel Password To set the control panel passwordCreating Local Presets Macros To create a new local presetAppendix a Managing Configuration Files Loading an .xcl Configuration File Device Discovery SupportAppendix B Programmer’s Interface for System Diagnostics System Component InformationUsing BCS to Access System Diagnostic Information ExampleSplash Screen Examples Display for v1i1 verbosity 1, componentDisplay for v3i5 verbosity 3, component It’s Your World Take Control