AMX Precis SD instruction manual Splash Screen Examples, Display for v1i1 verbosity 1, component

Page 62

Appendix B – Programmer’s Interface for System Diagnostics

Splash Screen Examples

Following are four examples of splash screen information that could be displayed when different verbosity/component settings are specified. Depending on the amount of detail provided, you may need to scroll to see the entire display. Use the first example to check the host software (IOS) version and the hardware driver (appcode) version.

~scrv1i1!

[1:Enclosure] AutoPatch Precis-500 [host software] v3.0.2 [hardware driver] v1.4.1 R [build date] Sep 22 2008 11:11:53 [xnet address] 0xa373

[ap system id] 0x0

[nvram status] valid.. user preferences restored [nvram magic] 0xdedafaba

FIG. 26 Display for v1i1 (verbosity 1, component 1)

~scrv3i3!
[3:Communication	Interfaces] count = 3
[interface 1]	detected
[type] BCS	mode RS232 port,	9600	(8/1/N/E/NS)
[interface 2]	detected
[type] MCF5272 FEC Ethernet		Controller
[interface 3]	detected
[type] Neuron bridge v1.0.3

FIG. 27 Display for v3i3 (verbosity 3, component3)

Precis SD Instruction Manual	57

Image 62

Contents Precis SD AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Contents Appendix a Managing Configuration Files ESD Warning Important Safety Information & Instructions Information et directives de sécurité importantes Usfcc Notice Copyright NoticeLiability Notice Lithium Batteries Notice Trademark NoticesPage Applicability Notice Overview & General SpecificationsPrecis SD Features Product NotesPrecis SD Control Features Front ViewCPU/Control Hardware Rear ViewRear View Components System Serial Number Power Receptacle & SpecificationsInput & Output Connectors Precis SD General Specifications General SpecificationsAMX Control Devices Configuration Information & Control OptionsFront Control Panel AMX Control SoftwareBCS Serial Control Protocol Third-Party Controllers Overview & General Specifications Site Recommendations Installation & SetupGeneral Hazard Precautions Reliable Earthing Grounding UnpackingCircuit Overloading Unpacking TipsOptional items for rack installation Rack Installation & System SetupRequired items for rack installation Installation RecommendationsInstallation Procedure To install and set up a Precis SD system in a rackAdditional Installation Options Attaching External Controllers PC Requirements for APControl RS-232 Pin DiagramAttaching Serial Controllers PC Requirements for BCSChange the enclosure’s settings instead, use XNConnect see To establish a Remote port connection with an XNNet device Attaching External XNNet ControllersCommunication Cable Requirements Signal Types & Connectors Attaching Inputs & OutputsCabling Video Connectors To connect video inputs and outputsAttaching Wires Wiring Audio ConnectorsWiring Sources & Destinations To attach stereo audio input and output wiresApplying Power & Startup Power-Up Sequence To apply powerAPWeb Serial Control Device StartupAPControl HyperTerminalExecuting a Test Switch Executing a Test SwitchAMX Control Device To execute a test switch using the control panelControl Panel APControl 3.0 or APWebTo execute a test switch using BCS commands BCS CommandsTo disconnect the factory default switch using BCS commands TroubleshootingTechnical Support AMX Contact InformationSync Specifications Signal SpecificationsUltra-Wideband 500 MHz Specifications Standard Audio Specifications Standard Audio Signal SpecificationsPrecis SD Control Panel Operation OverviewModes of Operation Audio Adjust Keys optionalControl Keys Virtual Matrices LevelsExecuting a Switch Executing & Disconnecting SwitchesSwitching Level To execute a switch selecting input source firstTo disconnect an output To execute a switch selecting output destination firstDisconnecting Outputs Verifying Signal Status To verify the status of a signalExecuting Macros Local Presets To adjust output volume Adjusting AudioAdjusting Output Volume To adjust digital input gain Adjusting Digital Input GainTo adjust digital input gain to equalize input levels Purpose & Uses of Input GainTo unlock the control panel Locking & Unlocking the Control PanelTo lock the control panel Precis SD Control Panel Operation Appendix a Managing Configuration Files Applicability NoticeSystem Requirements Installing & Launching XNConnectTo install XNConnect from the AMX AutoPatch CD To launch XNConnectDiscovering a System To discover a systemOpening an .xcl Configuration File To open an .xcl fileVirtual Matrix View Navigating the InterfaceHardware View To customize the channel names Modifying an .xcl Configuration FileModifying Source & Destination Channel Names Setting the Control Panel Password To set the control panel passwordCreating Local Presets Macros To create a new local presetAppendix a Managing Configuration Files Loading an .xcl Configuration File Device Discovery SupportAppendix B Programmer’s Interface for System Diagnostics System Component InformationUsing BCS to Access System Diagnostic Information ExampleSplash Screen Examples Display for v1i1 verbosity 1, componentDisplay for v3i5 verbosity 3, component It’s Your World Take Control