AMX Precis SD instruction manual Technical Support, AMX Contact Information

Page 37

Installation & Setup

Technical Support

Before contacting technical support with a question, please consult this manual. If you still have questions, contact your AMX representative or technical support. Have your system’s serial number ready. The system’s serial number is normally located in two places on the enclosure; on the left rear and on the left side (near the power receptacle).

We recommend recording your system’s serial number in an easily accessible location.

AMX Contact Information

3000 Research Drive, Richardson, TX 75082 800.222.0193 469.624.8000

Fax 469.624.7153

Technical Support 800.932.6993 www.amx.com

32

Precis SD Instruction Manual

Image 37
Contents Precis SD AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Contents Appendix a Managing Configuration Files ESD Warning Important Safety Information & Instructions Information et directives de sécurité importantes Liability Notice Copyright NoticeUsfcc Notice Trademark Notices Lithium Batteries NoticePage Precis SD Features Overview & General SpecificationsApplicability Notice Product NotesFront View Precis SD Control FeaturesRear View Components Rear ViewCPU/Control Hardware Input & Output Connectors Power Receptacle & SpecificationsSystem Serial Number General Specifications Precis SD General SpecificationsFront Control Panel Configuration Information & Control OptionsAMX Control Devices AMX Control SoftwareBCS Serial Control Protocol Third-Party Controllers Overview & General Specifications General Hazard Precautions Installation & SetupSite Recommendations Circuit Overloading UnpackingReliable Earthing Grounding Unpacking TipsRequired items for rack installation Rack Installation & System SetupOptional items for rack installation Installation RecommendationsTo install and set up a Precis SD system in a rack Installation ProcedureAdditional Installation Options Attaching External Controllers Attaching Serial Controllers RS-232 Pin DiagramPC Requirements for APControl PC Requirements for BCSChange the enclosure’s settings instead, use XNConnect see Communication Cable Requirements Attaching External XNNet ControllersTo establish a Remote port connection with an XNNet device Attaching Inputs & Outputs Signal Types & ConnectorsTo connect video inputs and outputs Cabling Video ConnectorsWiring Sources & Destinations Wiring Audio ConnectorsAttaching Wires To attach stereo audio input and output wiresPower-Up Sequence To apply power Applying Power & StartupAPControl Serial Control Device StartupAPWeb HyperTerminalExecuting a Test Switch Executing a Test SwitchControl Panel To execute a test switch using the control panelAMX Control Device APControl 3.0 or APWebTo disconnect the factory default switch using BCS commands BCS CommandsTo execute a test switch using BCS commands TroubleshootingAMX Contact Information Technical SupportUltra-Wideband 500 MHz Specifications Signal SpecificationsSync Specifications Standard Audio Signal Specifications Standard Audio SpecificationsOverview Precis SD Control Panel OperationControl Keys Audio Adjust Keys optionalModes of Operation Virtual Matrices LevelsSwitching Level Executing & Disconnecting SwitchesExecuting a Switch To execute a switch selecting input source firstDisconnecting Outputs To execute a switch selecting output destination firstTo disconnect an output To verify the status of a signal Verifying Signal StatusExecuting Macros Local Presets Adjusting Output Volume Adjusting AudioTo adjust output volume To adjust digital input gain to equalize input levels Adjusting Digital Input GainTo adjust digital input gain Purpose & Uses of Input GainTo lock the control panel Locking & Unlocking the Control PanelTo unlock the control panel Precis SD Control Panel Operation Applicability Notice Appendix a Managing Configuration FilesTo install XNConnect from the AMX AutoPatch CD Installing & Launching XNConnectSystem Requirements To launch XNConnectTo discover a system Discovering a SystemTo open an .xcl file Opening an .xcl Configuration FileHardware View Navigating the InterfaceVirtual Matrix View Modifying Source & Destination Channel Names Modifying an .xcl Configuration FileTo customize the channel names To set the control panel password Setting the Control Panel PasswordTo create a new local preset Creating Local Presets MacrosAppendix a Managing Configuration Files Device Discovery Support Loading an .xcl Configuration FileSystem Component Information Appendix B Programmer’s Interface for System DiagnosticsExample Using BCS to Access System Diagnostic InformationDisplay for v1i1 verbosity 1, component Splash Screen ExamplesDisplay for v3i5 verbosity 3, component It’s Your World Take Control