Paxar 611, 610, 612 user manual Data Formatting Errors

Page 57

Data Formatting Errors

Errors 571 to 618 are data formatting errors. This type of error happens when a field prints incorrectly. Your System Administrator can correct the format, batch, or graphic packet and send the print job again. For errors 571 to 614, the printer will still print, but the data may be incomplete, missing, or wrong.

Error Description/Action

571UPC or EAN bar code data length in the batch doesn’t fit the format.

572Batch data doesn’t fit the format, the field contains blanks, or data mismatch.

573Batch data in price field doesn’t fit the format or the field contains blanks.

574Batch data in check digit scheme doesn’t fit the format, or the field contains blanks.

575The graphic included in your format could not be found.

600Imaging error because the batch was refused.

601An error occurred while the batch was imaging.

602The batch was not found during imaging.

611Font, bar code, or density in the batch doesn’t fit the format.

612Batch data is missing or doesn’t match the format.

613Reference point off tag.

614Portion of field off tag.

615Bar code width is greater than 16 inches, or keywords of PDF417 bar code exceed 928.

616A bad dot falls on a bar code that cannot be shifted. Call Service or replace the printhead.

618

Magnification must be 1 to 7.

620Font and printhead density mismatch. Check the font or verify the correct printhead (203 dpi or 300 dpi) is installed.

Users Manual - 610/611/612 Printers

Troubleshooting ∙ 53

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Paxar Systems Group Manual Edition March 610 / 611 / 612 PrintersThis page left blank intentionally Contents Troubleshooting Appendix a Specifications & AccessoriesContacting Paxar Getting Started Connecting the Power Cable AudienceUnpacking the Printer Connecting the Communication Cable Default Serial Port Communication ValuesEstablishing Communications Default Printer Settings Using the Control PanelPrinter Status Lights Status Code Box Button FunctionsSetting Dip Switches DIP Switches Diagnostics Lower DIP Switches Flow ControlFeed Mode VerifierLoading Supplies Loading Labels 610 Do not pick up the printer By the supply holder Peel Bar Ribbon Bar Loading Supplies ∙ 14 ∙ Loading Supplies Loading Labels 16 ∙ Loading Supplies Loading Supplies ∙ 18 ∙ Loading Supplies Loading Supplies ∙ Loading Ribbon Loading Supplies ∙ Take-up Reel Back Reel Loading Supplies ∙ Adjusting the Wide/Narrow Knobs Loading Supplies ∙ Printing PrintingPrinter Alignment Top and Bottom Copy Printing an Error LabelPreventing Jams Non-Printing ZonePrinting Serial Bar Codes Adjusting Print PositionsSupply Position Adjusting the Cut AnglePrint Position Margin PositionAdjusting the Drop Tray Using the KnifeCare Symbol Font Samples Ginetex FontNafta Font Care and Maintenance Clearing a Knife Jam Clearing Supply JamsCleaning 36 ∙ Care and Maintenance Replacing the Printhead 38 ∙ Care and Maintenance Care and Maintenance ∙ Snap the printhead into place Adjusting the Print Contrast Replacing the Fuse Lubricating the Knife Troubleshooting Printing a Test Label Problem Action TroubleshootingData Errors Error MessagesOption number must be 1, 4, 30, 31, 42, 50, 60, or Troubleshooting ∙ 50 ∙ Troubleshooting Troubleshooting ∙ Communication Failures Error Description/ActionData Formatting Errors Machine Faults Troubleshooting ∙ Printer Specifications Appendix a Specifications & AccessoriesPaxar Systems Supply SpecificationsRibbon Widths Ribbon SpecificationsContacting Paxar Accessories
Top Page Image Contents