Paxar 610, 611, 612 user manual Machine Faults

Page 58

Machine Faults

Errors 700 to 765 happen when there is a problem with the printer.

Error Description/Action

700An error is pending and the printer cannot continue with the batch.

701Printer received a command that it cannot execute while it is running.

702Check your printer’s SETUP settings.

703The printer sensed a calibration of different-sized black marks.

704Printer didn’t detect a sense mark within the maximum feed length or out of supplies. Check or load supplies.

705Invalid batch received.

750Printhead is overheated. Turn off the printer and let it cool.

751Printer didn’t detect a sense mark when expected.

752Printer detected a sense mark in the wrong place.

753Printer detected a sense mark that is too long.

754Out of ribbon or ribbon jam. Check or load ribbon. Remove any slack in the ribbon by turning the take-up reel clockwise. Load a new ribbon.

755Printhead is open. Close the printhead.

756Out of supplies. Load supplies.

757Reload supplies (supply length mismatch).

758The supply was not seen or the On-Demand sensor is not working correctly. Check for a supply jam. Clear the supply path or reload supplies. This error may occur if you remove a label too quickly in the On-Demand mode. The printer does not recalibrate after this error.

759Knife is not moving. Call Technical Support.

760Knife jam. Call Technical Support.

761Stacker is full or jammed. Empty the stacker before continuing.

762Low battery. Recharge the battery.

763Waiting to dispense label. Press Feed.

764Verifier failure. Call Technical Support.

765The printhead has less than four bad spots. The printer can shift bar code fields to avoid bad dots. Press Clear to continue printing. Print a test label to confirm the number of bad dots.

54 ∙ Troubleshooting

Users Manual - 610/611/612 Printers

Page 57 Page 59
Image 58
Page 57 Page 59
Contents 610 / 611 / 612 Printers Paxar Systems Group Manual Edition MarchThis page left blank intentionally Contents Appendix a Specifications & Accessories TroubleshootingContacting Paxar Getting Started Audience Connecting the Power CableUnpacking the Printer Default Serial Port Communication Values Connecting the Communication CableEstablishing Communications Using the Control Panel Default Printer SettingsPrinter Status Lights Button Functions Status Code BoxSetting Dip Switches DIP Switches Feed Mode Lower DIP Switches Flow ControlDiagnostics VerifierLoading Supplies Loading Labels 610 Do not pick up the printer By the supply holder Peel Bar Ribbon Bar Loading Supplies ∙ 14 ∙ Loading Supplies Loading Labels 16 ∙ Loading Supplies Loading Supplies ∙ 18 ∙ Loading Supplies Loading Supplies ∙ Loading Ribbon Loading Supplies ∙ Take-up Reel Back Reel Loading Supplies ∙ Adjusting the Wide/Narrow Knobs Loading Supplies ∙ Printing PrintingPrinting an Error Label Printer Alignment Top and Bottom CopyNon-Printing Zone Preventing JamsAdjusting Print Positions Printing Serial Bar CodesPrint Position Adjusting the Cut AngleSupply Position Margin PositionUsing the Knife Adjusting the Drop TrayGinetex Font Care Symbol Font SamplesNafta Font Care and Maintenance Clearing Supply Jams Clearing a Knife JamCleaning 36 ∙ Care and Maintenance Replacing the Printhead 38 ∙ Care and Maintenance Care and Maintenance ∙ Snap the printhead into place Adjusting the Print Contrast Replacing the Fuse Lubricating the Knife Troubleshooting Printing a Test Label Troubleshooting Problem ActionError Messages Data ErrorsOption number must be 1, 4, 30, 31, 42, 50, 60, or Troubleshooting ∙ 50 ∙ Troubleshooting Troubleshooting ∙ Error Description/Action Communication FailuresData Formatting Errors Machine Faults Troubleshooting ∙ Appendix a Specifications & Accessories Printer SpecificationsSupply Specifications Paxar SystemsRibbon Specifications Ribbon WidthsAccessories Contacting Paxar
Top Page Image Contents