3Com 6200 manual Connector Pin Assignments, DB-9 Connector, Pin Number, Signal

Page 75

Connector Pin Assignments


		B
	Connector Pin Assignments	B
	Connector Pin Assignments

This appendix describes the craft port pin assignments:

The Craft port, located on the front of the system, uses a DB- 9 connector with the following pin identifications and associated signals.

DB-9 Connector	Pin Number	Signal
	1	No Connection
	2	TDX
	3	RXD
	4	DSR
	5	GND
	6	DTR
	7	CTS
	8	RTS
	9	No Connection

3COM Security Switch 6200 Hardware and Software Users Guide

B-1

Image 75

Contents FIBER Security Switch Hardware and Software Users Guides10/100 10/100/1000Regulated Materials Statement UNITED STATES GOVERNMENT LEGENDENVIRONMENTAL STATEMENT End of Life StatementAbout this Guide ContentsInstallation 3COM Security Switch 6200 Hardware and Software Users GuideTechnical Support 4 Configuring the Security Switch 6200 SystemTechnical Specifications 5 Upgrading the System SoftwareRegulatory Standards Compliance Connector Pin AssignmentsRegulatory Information Safety3COM Security Switch 6200 Hardware and Software Users Guide Conventions About this GuideIntended AudienceSecurity Switch 6200 Applications Guide 3COM Security Switch 6200 Hardware and Software Users GuideSecurity Switch 6200 Product Release Notes Install Server Installation and Configuration GuideIntroduction SystemComponents Chassis Figure 1-1 6200 Front ViewFigure 1-2 Rear Panel Component Layout Configuration Tool Management OptionsFirst Time Startup Interview Introduction Before You Start InstallationSite Requirements RequirementDescription FIBER Figure 2-1 3COM Security Switch 6200 Shipping ContentsMGMT1 MGMT2 SYS HDD 10/100Table 2-1 Cable Distance Limitations Additional Equipment Required EquipmentTools CablesFigure 2-2 Front Rack Mounting the Chassis InstallationTerminal or PC Front Rack MountingTabletop Mounting Interface Connections and First Time Start-Up Making ConnectionsManagement Serial Port Connections Connecting a Terminal or PC to the System Front Serial Craft Port Figure 3-3 System Rear View Power Connections Connecting RemotelyPower Connections Figure 3-2 Connecting to the System RemotelyLED Displays Startup andNormal OperationBMC Generated POST Beep Codes POST Error Beep CodesBIOS Generated POST Error Beep Codes Error messageInterface Connections and First Time Start-Up Debug port 80h POST Memory Error 3-Beep Codeserror Codes BeepFirst Time Startup 3. Define the Time Zone 4. Select a region 3-105. Define the Management Services 6. Configure the SNMP parameters8. Configure the host interfaces 3-117. Configure the individual user accounts The following is an example display showing configured users3-12 9. Configure all additional interfaces10. Configure your default gateway 11. Configure NTP to achieve time synchronization 3-133-14 Configuring the Security Switch System Configuring Parameterschoices. The Enter key is used to select default values 2. To change any of the system parameters enter y, or press the Return key to leave system parameters unchanged 3COM Security Switch 6200 Hardware and Software Users Guide Configuring User Accounts Domain Name Resolutionthe Network Time Protocol3. Enter the desired option or enter X to return to the main menu Configuring the Simple Network Management Protocol SNMPTo configure SNMP 1. Select Option 5 from the main menu 2. Configure SNMP Servers. For example4. Configure SNMP Communities. For example 6. Configure SNMP Trap Destinations. For example 4-10 Interfaces4-11 1. Select Option 7 from the main menu 4-124-13 Configuring Network InterfacesIP Aliases 4-14interface. To configure IP Aliases 4-15 4-16 Configuring Static Routes4-17 Configuring Static ARP Entries4-18 Configuring the Virtual Router Redundancy Protocol VRRP4-19 4-20 Restoring Saving Your System ConfigurationConfiguration Exiting from the Configuration Tooladdress=10.1.1.50 data /dnsserver 4-22ipinterface data ifname=management 1 address=192.168.10.6 /data 4-23ipaddr=128.205.1.31 macaddr=0000a2000003 /data statichost account 4-24Factory DefaultSettings system to4-26 Upgrading the System Software Upgrading the System SoftwareAnswer Y when this command prompts you Upgrading from Version Upgrading the System Software Using the Safe Upgrade andRollback Features Software Safe Upgrade6. Savew the partition table by entering the letter “w” Upgrading from Version 2.1 and Greater Upgrading from Software to a UP While an RP is Operational Rollback Technical ServicesTechnical Support OnlineSupplier 3Com Knowledgebase Web ServicesSupport from Your NetworkAsia, Pacific Rim Support from 3ComEmail Support Telephone SupportAsia, Pacific Rim Telephone Support NumbersCountry Telephone NumberNorth America Latin AmericaReturning Products for Repair Fax Numbers for return authorization numbersTelephone Number 3COM Security Switch 6200 Hardware and Software Users GuideTechnical Support CountryTechnical Support Power Characteristics Technical SpecificationsPhysical Characteristics Environmental CharacteristicsTechnical Specifications Pin Number Connector Pin AssignmentsDB-9 Connector SignalConnector Pin Assignments CE marking for the EEA European Economic Area SafetyRegulatory Information Regulatory Standards ComplianceVCCI Statement V-3/2000.04 EMI ComplianceImmunity Compliance Radio Frequency Interference