SMC Networks EX500-GEN1 instruction manual Input Unit Manifold Part Names

Page 15

Input Unit Manifold Part Names

The Input unit manifold consists of Input unit, input block (s), end block and DIN rail. The input block up to 8 can be connected ( 16 points ).

Any combination of input blocks ( for M8 connector, M12 connector and 8-point- integrated type ) is acceptable.

Note Do not mix sensor input specifications ( PNP and NPN ).

Figure shows the configuration when only input blocks for M8 connector are connected.

No.

Part name

Application

1

Input unit

Unit to communicate with GW unit or SI unit.

 

 

 

2

Communication

To be connected with branch cables from GW unit or

 

connector

SI unit ( branch cable with M12 connector ). ( Note1 )

 

 

 

3

Power LED

Indicates the power supply status. ( Note2 )

 

 

 

4

Input block

Unit for sensor signal input.

 

 

 

5

Sensor connector

Connects with sensor. ( Note1 )

 

 

 

6

Indicator LED

Indicates sensor signal status. ( Note2 )

 

 

 

7

Marker

To be used for writing input No. etc.

 

 

 

8

End block

Composes the end of Input unit manifold.

 

 

 

9

DIN rail

To be mounted with Input unit manifold.

 

 

 

Note1 : For wiring method, refer to subsection "Wiring" ( page 30 ) of section "Input Unit Manifold" in this manual.

Note2 : For display, refer to "Display" ( page 31 ) in section "Input Unit Manifold" in this manual.

Dimensions ( unit : mm )

When only input blocks for M8 connector are connected

 

DIN Rail

35

49

L3

(L4)

L2 ( Rail mounting pitch: 12.5 )

5

L1

 

44.2

(7.5)

32.2

39.7

 

Stations

1

2

3

4

5

6

7

8

L1

[mm] : Rail length

98

110.5

123

135.5

148

160.5

173

185.5

 

 

 

 

 

 

 

 

 

 

L2

[mm] : Mounting pitch

87.5

100

112.5

125

137.5

150

162.5

175

 

 

 

 

 

 

 

 

 

 

L3

[mm] : Manifold length

74

86

98

110

122

134

146

158

 

 

 

 

 

 

 

 

 

 

L4

[mm]

12

12

12.5

12.5

13

13

13.5

13.5

 

 

 

 

 

 

 

 

 

 

When only input blocks of 8-point-integrated type are connected

 

Stations

1

2

L1

[mm] : Rail length

135.5

185.5

 

 

 

 

L2

[mm] : Mounting pitch

125

175

 

 

 

 

L3

[mm] : Manifold length

110

158

 

 

 

 

L4

[mm]

12.5

13.5

 

 

 

 

26

27

Image 15
Contents Reduced wiring system Contents Otherwise injury can result Do not operate beyond specification rangeOtherwise injury or failure can result Otherwise accident caused by malfunction can resultManifold valve with SI unit SV/VQC series SafetySystem configuration general Product SummaryEX500 body Dimensions unit mmInstallation unit mm EX500 Part NamesMapping SpecificationBasic specifications Higher-level busLower-level bus WiringSpecification Wirings is explained in the following orderCable connection WiringCommunication wiring Power supply wiringBranch wiring Single power suppliesCable plug For GW unit Input unit manifold configuration For GW unit Manifold valve Input unit manifold configurationDisplay/Switch Setting Switch settingDisplay SI unit for SV series valves EX500-S Display/Switch SettingDefault settings SI Unit Part NamesMounting/Wiring EX500-QMounting and removing methods of SI unit are as shown below Applicable valve series DisplaySI unit for SV series valve EX500-S SI unit for VQC series valve EX500-QInput Unit Manifold Part Names When only input blocks for M8 connector are connectedSpecifications for Input unit InstallationDimensions unit mm When only input blocks for M12 connector are connectedConnect sensors to the sensor Sensor wiringLights off Sensor signal input OFF logical Correspondence between input number and input blockEX9-PE1 EX9-OET1/EX9-OET2 EX9-PE1Part name Application Mounting Output wiringEX9-OEP1/EX9-OEP2 output connectors Dimensions when general purpose output block is connectedEX9-PE1 power input connector No.1 EX9-PE1 power supply connector No.0PWR EX9-OET1 EX9-OET2 EX9-OEP1 EX9-OEP2Option COM a D LED TroubleshootingOverall system EtherNet/IP compatible communication