SMC Networks EX500-GEN1 instruction manual Option

Page 22

Option

Cable with Ethernet communication connector

For details, refer to subsection "Wiring" ( page 12 ) in section "EX500" in this manual.

How to order

EX9-AC 020 EN - PSRJ

Cable length (L)

Connector specification

020

2 [m]

PSRJ

M12 plug(straight)

RJ45 connector

Branch cable with M12 connector

For details, refer to subsection "Wiring" ( page 17 ) in section "EX500" in this manual.

How to order

EX500-AC 030 - SSPS


Cable length (L)												Connector specification
Cable length (L)												Connector specification
	003	0.3	[m]									SSPS		Socket side : Straight, Plug side : Straight
	005	0.5	[m]									SAPA		Socket side : Angle, Plug side : Angle
	010	1	[m]
	030	3	[m]
	050	5	[m]

Power supply connector cable

For details, refer to subsection "Wiring" ( page 13 ) of section "EX500" in this manual.

How to order

EX500-AP 050 - S


Cable length (L)								Connector specification
Cable length (L)								Connector specification
	010	1 [m]						S		Straight
	050	5 [m]						A		Angle

Output Cable

For details, refer to subsection "Wiring" ( page 35 ) of section "EX9 series General Purpose Output Block" in this manual.

How to order

EX9-AC 010 -7

Cable length ( L )

010	1 [m]
030	3 [m]

Power Supply Cable ( for power input connector of Power Block )

For details, refer to subsection "Wiring" ( page 37 ) of section "EX9 series General Purpose Output Block" in this manual.

How to order

EX9-AC 010 -1

Cable length ( L )

010	1 [m]
030	3 [m]
050	5 [m]

6Terminal Plug

Connected to C1 ( or 0 ) of SI unit when Input unit manifold is unused. ( If this terminal plug is not used, COM LED of GW unit does not light on. )

How to order

EX500 - AC000 - S

8	2	1	M12

3		7	16
4		6

		5
Plug Connector Pin Layout			44.7

7Waterproof cap

Mounted on unused ports of GW unit, input block, power block and output block. The proper use of this waterproof cap can achieve IP65 Enclosure.

How to order

EX500-AW

Connector specification

ES	M8 connector ( socket ) /10 pcs.
TP	M12 connector ( plug ) /1 pc.
TS	M12 connector ( socket ) /10 pcs.

NOTE

Tighten the waterproof cap by the specified tightening torque. ( 0.05Nm for M8, 0.1Nm for M12 )

40

41

Image 22

Contents Reduced wiring system Contents Otherwise accident caused by malfunction can result Do not operate beyond specification rangeOtherwise injury or failure can result Otherwise injury can resultProduct Summary SafetySystem configuration general Manifold valve with SI unit SV/VQC seriesEX500 Part Names Dimensions unit mmInstallation unit mm EX500 bodyHigher-level bus SpecificationBasic specifications MappingWirings is explained in the following order WiringSpecification Lower-level busPower supply wiring WiringCommunication wiring Cable connectionSingle power supplies Branch wiringCable plug For GW unit Manifold valve Input unit manifold configuration For GW unit Input unit manifold configurationSwitch setting Display/Switch SettingDisplay SI Unit Part Names Display/Switch SettingDefault settings SI unit for SV series valves EX500-SEX500-Q Mounting/WiringMounting and removing methods of SI unit are as shown below SI unit for VQC series valve EX500-Q DisplaySI unit for SV series valve EX500-S Applicable valve seriesWhen only input blocks for M8 connector are connected Input Unit Manifold Part NamesWhen only input blocks for M12 connector are connected InstallationDimensions unit mm Specifications for Input unitCorrespondence between input number and input block Sensor wiringLights off Sensor signal input OFF logical Connect sensors to the sensorEX9-OET1/EX9-OET2 EX9-PE1 EX9-PE1Part name Application Dimensions when general purpose output block is connected Output wiringEX9-OEP1/EX9-OEP2 output connectors MountingEX9-PE1 power supply connector No.0 EX9-PE1 power input connector No.1EX9-OET1 EX9-OET2 EX9-OEP1 EX9-OEP2 PWROption EtherNet/IP compatible communication TroubleshootingOverall system COM a D LED