Seagate ST400FX0012, ST100FX0002, ST200FX0002, ST400FX0002 manual Scope

Page 10

2.0Scope

This manual describes Seagate Technology® LLC, Pulsar® XT.2 SAS (Serial Attached SCSI) drives.

Pulsar XT.2 drives support the SAS Protocol specifications to the extent described in this manual. The SAS Interface Manual (part number 100293071) describes the general SAS characteristics of this and other Sea- gate SAS drives. The Self-Encrypting Drive Reference Manual, part number 100515636, describes the inter- face, general operation, and security features available on Self-Encrypting Drive models.

Product data communicated in this manual is specific only to the model numbers listed in this manual. The data listed in this manual may not be predictive of future generation specifications or requirements. If you are designing a system which will use one of the models listed or future generation products and need further assistance, please contact your Field Applications Engineer (FAE) or our global support services group as shown in Section 1.0.

Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models.

Standard models

Standard SED models

ST400FX0002	ST400FX0012

ST200FX0002

ST100FX0002

Note. Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption (FDE) models before a differentiation between drive-based encryption and other forms of encryp- tion was necessary.

Note. The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for “Security of Data at Rest” based on the standards defined by the Trusted Computing Group (see www.trustedcomputinggroup.org).

2	Pulsar XT.2 SAS Product Manual, Rev. B

Image 10

Contents ST400FX0002ST400FX0012 ST200FX0002 ST100FX0002 Standard Models Self-Encrypting Drive ModelsRevision history Contents Installation Physical/electrical specificationsDefect and error management About self-encrypting drivesPage Pulsar XT.2 SAS Product Manual, Rev. B List of Figures Page Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCReference documents China Restriction of Hazardous Substances RoHS DirectiveStandard features General descriptionPerformance Media descriptionReliability Formatted capacities Factory-installed optionsProgrammable drive capacity Thin Provisioning Drive Configuration Performance characteristics Performance characteristicsInternal drive characteristics Access timeFormat Mode Dcrt Bit IP Bit 400GB 200GB 100GB PerformanceCache control Start/stop timeCaching write data Reliability specifications Error ratesEndurance Management Data Retention Reliability and servicePreventive maintenance Lifetime Endurance ManagementControlling S.M.A.R.T Maximum processing delay Fully-enabled delay4 S.M.A.R.T Performance impactPredictive failures Thermal monitorDST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct repair and return information Product warrantyShipping StoragePower specifications Physical/electrical specificationsAC power requirements DC power requirements 400GB standard model DC power requirements200GB standard model DC power requirements 100GB standard model DC power requirements Conducted noise immunity General DC power requirement notesPower sequencing Current profilesCurrent profiles for 200GB models 400GB models in 6Gb operation Power dissipation200GB models in 6Gb operation Environmental limits Temperature a. Operating100GB models in 6Gb operation Effective altitude sea level a. Operating Relative humidityShock and vibration Shock Recommended mountingVibration a. Operating-normal Air cleanlinessCorrosive environment Mechanical specifications Mounting configuration dimensions 400GB modelsWeight Pounds 100 grams About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDrive internal defects/errors Defect and error managementSSD Physical format address descriptor Bit Byte Background Media Scan Drive error recovery proceduresSAS system errors Auto-ReallocationLevels of PI Setting and determining the current Type LevelProtection Information PI Identifying a Protection Information driveInstallation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsPersistent Reserve Read Capacity Write Mode Sense data Inquiry dataPage Mode Sense data for 400GB drives 14 1a 00 1aMode Sense data for 200GB drives Mode PagesMode Sense values for 100GB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interfaceDatum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification complianceLED drive signal General interface characteristicsIndex NumericsPage RNG See also cooling Page Seagate Technology LLC Americas