Seagate ST200FX0002 Reference documents, China Restriction of Hazardous Substances RoHS Directive

Page 13

3.1.4 China Restriction of Hazardous Substances (RoHS) Directive

This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard.

"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined by the China RoHS MCV Standard.

"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the threshold defined by the China RoHS MCV Standard.

3.2	Reference documents
SCSI Commands Reference Manual		Seagate part number: 100293068
SAS Interface Manual		Seagate part number: 100293071
ANSI SAS Documents
	SFF-8223	2.5” Drive Form Factor with Serial Connector
	SFF-8460	HSS Backplane Design Guidelines
	SFF-8470	Multi Lane Copper Connector
	SFF-8482	SAS Plug Connector
	ANSI INCITS.xxx	Serial Attached SCSI (SAS-2) Standard (T10/1760-D)
	ISO/IEC 14776-xxx SCSI Architecture Model-3 (SAM-4) Standard (T10/1683-D)
	ISO/IEC 14776-xxx SCSI Primary Commands-3 (SPC-4) Standard (T10/1731-D)
	ISO/IEC 14776-xxx SCSI Block Commands-3 (SBC-3) Standard (T10/1799-D)
ANSI Small Computer System Interface (SCSI) Documents
	X3.270-1996	(SCSI-3) Architecture Model

Trusted Computing Group (TCG) Documents (apply to Self-Encrypting Drive models only) TCG Storage Architecture Core Specification, Rev. 1.0

TCG Storage Security Subsystem Class Enterprise Specification, Rev. 1.0

Self-Encrypting Drives Reference Manual

Seagate part number: 100515636

JEDEC Standards

JESD218 - Solid-State Drive (SSD) Requirements and Endurance Test Method JESD219 - Solid-State Drive (SSD) Endurance Workloads

In case of conflict between this document and any referenced document, this document takes precedence.

Pulsar XT.2 SAS Product Manual, Rev. B

5

Image 13

Contents Standard Models Self-Encrypting Drive Models ST400FX0002ST400FX0012 ST200FX0002 ST100FX0002Revision history Contents Defect and error management Physical/electrical specificationsInstallation About self-encrypting drivesPage Pulsar XT.2 SAS Product Manual, Rev. B List of Figures Page Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCChina Restriction of Hazardous Substances RoHS Directive Reference documentsGeneral description Standard featuresPerformance Media descriptionReliability Formatted capacities Factory-installed optionsProgrammable drive capacity Thin Provisioning Drive Configuration Internal drive characteristics Performance characteristicsPerformance characteristics Access timePerformance Format Mode Dcrt Bit IP Bit 400GB 200GB 100GBCache control Start/stop timeCaching write data Error rates Reliability specificationsEndurance Management Preventive maintenance Reliability and serviceData Retention Lifetime Endurance Management4 S.M.A.R.T Maximum processing delay Fully-enabled delayControlling S.M.A.R.T Performance impactThermal monitor Predictive failuresDrive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesShipping Product warrantyProduct repair and return information StoragePower specifications Physical/electrical specificationsAC power requirements 400GB standard model DC power requirements DC power requirements200GB standard model DC power requirements 100GB standard model DC power requirements Power sequencing General DC power requirement notesConducted noise immunity Current profilesCurrent profiles for 200GB models 400GB models in 6Gb operation Power dissipation200GB models in 6Gb operation Environmental limits Temperature a. Operating100GB models in 6Gb operation Effective altitude sea level a. Operating Relative humidityShock and vibration Recommended mounting ShockVibration a. Operating-normal Air cleanlinessCorrosive environment Mounting configuration dimensions 400GB models Mechanical specificationsWeight Pounds 100 grams Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDrive internal defects/errors Defect and error managementSSD Physical format address descriptor Bit Byte SAS system errors Drive error recovery proceduresBackground Media Scan Auto-ReallocationProtection Information PI Setting and determining the current Type LevelLevels of PI Identifying a Protection Information driveDrive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedPersistent Reserve Read Capacity Write Inquiry data Mode Sense dataPage 14 1a 00 1a Mode Sense data for 400GB drivesMode Pages Mode Sense data for 200GB drivesMode Sense values for 100GB drives Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interfaceDatum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification complianceDifferential signals General interface characteristicsNumerics IndexPage RNG See also cooling Page Americas Seagate Technology LLC