Net Optics none manual Director Rear Panel, Xfp

Page 14

Director

Director Rear Panel

The features of the Director rear panel are shown in the following diagram.

		2 XFP
Management		Daisy-chain	Power Supply	Power Supply
USB Port	Port	10GbE Ports	Module	Module
RS232	Management	INPUT OUTPUT
	Port
		SERIAL	XXXXXX
		NUMBER	XXXXXX
		NUMBER
RS-232 Port		SR, LR, or ER	Redundant Hot-swappable
RS-232 Port			Redundant Hot-swappable
	Fiber XFP Modules		Power Supplies
			Power Supplies

Figure 7: Director Rear Panel

Major features of the rear panel include:

•USB Port—Reserved for future functionality

•RS-232Port—DB9 serial port for the CLI

•Management Port—A 10/100/1000 network port for the remote management interfaces and software updates; the CLI runs over an SSH connection through this port; Compass management tools, when available, will connect through this port

•XFP Daisy-chain 10GbE Ports—Accepts SR, LR, and ER XFP transceiver modules for daisy-chaining up to

10 chassis

•Power Supply Modules—Universal-input (100-240VAC, 0.5Amp, 47-63Hz), hot-swappable power supplies with integrated cooling fans; each supply can power the unit independently; dual supplies provide redundancy to maximize uptime; -48VDC models are also available

10

*** Confidential - DO NOT Distribute ***

Image 14

Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix C Appendix aAppendix B Filter parametersChapter Introduction Monitor port Filtering Key FeaturesEase of Use Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools External Network Tap method IBypass Switch MethodIn-line Monitoring of 10 Gigabit Links Monitor Port LEDs Power LEDsDirector Front Panel DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceRack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect Power to Director Connect the local CLI InterfaceTip Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control To connect the CLI for remote use over the Management portLog into the CLI To log into the CLITo change the user name and password Configure Director using the CLIChange Director User Name and Password To assign a new Manager IP address to Director To change the port modeAssign a New Manager IP Address Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Current config fileConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkConnect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsNetwork Port 11 XFP Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersEnter filter list to view the pending filter list User interactions Filter capacityDaisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisCertifications Specifications, DNMEnvironmental Available ModelsAppendix B Command Line Interface Command Sub-Command Parameters Example and descriptionFilter add ipv6=n inports=n1.1-n1.3 ip Command may includeFilter add and filter ins commands Src=10.1.1.1 action=dropFilter running Load myconfiguration-1Filter list Filter syncPasswd Save myconfiguration-1Show myconfiguration-1 PingSysip show Sysip commitSysip ipaddr=192.168.1.2 netmask=255.255.0.0 TimeUser add name=bob pw=bob-pw priv=3 This This command is only available at root level CommandUser show Is onlyFilter parameters Director Filter Parameters Qual Value Example DescriptionAppendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved