Net Optics none manual About this Guide, Description

Page 7

Director

About this Guide

Please read this entire guide before installing Director. This guide applies to the following part numbers:

Chassis Part Number	Description

DIR-3400	Director Main Chassis with 10 SFP monitor ports
DIR-____	Director Main Chassis with 10 SFP monitor ports, -48VDC power
DIR-7400	Director Main Chassis with 10 SFP monitor ports, 2 XFP 10GbE ports, 2 XFP uplink ports
DIR-____	Director Main Chassis with 10 SFP monitor ports, 2 XFP 10GbE ports, 2 XFP uplink ports,
	-48VDC power
DNM Part Number	Description

DNM-100	6-Port 10/100/1000 Copper In-Line Module
DNM-110	12-Port 10/100/1000 Copper Span Module
DNM-200	6-Port Gigabit SX Fiber 62.5μm In-Line Module
DNM-210	12-Port Gigabit SX Fiber 62.5μm Span Module
DNM-220	6-Port Gigabit SX Fiber 50μm In-Line Module
DNM-230	12-Port Gigabit SX Fiber 50μm Span Module
DNM-300	6-Port Gigabit LX Fiber In-Line Module
DNM-310	12-Port Gigabit LX Fiber Span Module
DNM-320	6-Port Gigabit ZX Fiber In-Line Module
DNM-330	12-Port Gigabit ZX Fiber Span Module

3

*** Confidential - DO NOT Distribute ***

Image 7

Contents Smart Filtering Appliance Trademarks and Copyrights Contents Filter parameters Appendix aAppendix B Appendix CChapter Introduction Passive, Secure Technology Key FeaturesEase of Use Monitor port FilteringDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links IBypass Switch MethodExternal Network Tap method DNM / Network Port LEDs Power LEDsDirector Front Panel Monitor Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorTo connect the CLI for remote use over the Management port Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control TipTo log into the CLI Log into the CLIChange Director User Name and Password Configure Director using the CLITo change the user name and password Change Port Modes To change the port modeAssign a New Manager IP Address To assign a new Manager IP address to DirectorSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandCurrent config file Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsNetwork Port 11 XFP Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationEnter filter list to view the pending filter list Filter capacity User interactionsDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsAvailable Models Specifications, DNMEnvironmental CertificationsCommand Sub-Command Parameters Example and description Appendix B Command Line InterfaceSrc=10.1.1.1 action=drop Command may includeFilter add and filter ins commands Filter add ipv6=n inports=n1.1-n1.3 ipFilter sync Load myconfiguration-1Filter list Filter runningPing Save myconfiguration-1Show myconfiguration-1 PasswdTime Sysip commitSysip ipaddr=192.168.1.2 netmask=255.255.0.0 Sysip showIs only This This command is only available at root level CommandUser show User add name=bob pw=bob-pw priv=3Director Filter Parameters Qual Value Example Description Filter parametersNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved