Net Optics none manual Using the CLI Help Command, To view CLI help information

Page 24

Director

Using the CLI Help Command

To view CLI help information:

1.Enter Help at the "Net Optics:" prompt. The list of help topics is displayed.

Net Optics> help
![#]	- !number or up/down key for previous command
commit	- save local config to hardware
date	- set system date
del	- delete file 'name'
filter	- set for filter command
help	- view cli usage
history	- display command history list
image	- switch image
list	- list xml file
load	- load file 'name'
logout	- logout from cm server
module	- show installed modules in the system
passwd	- change password for ssh user's account
ping	- ping 'ipaddr'
port	- set port command
restart	- restart the whole system
save	- save file 'name'
show	- show all files 'name'
stats	- show/clear ports statistics
sysip	- show and set system network IP address
time	- set system time
upgrade	- upgrade image file
user	- manage user account
quit or exit	- exit current cli session
Net Optics>

Figure 16: Director CLI Help command

2.To view the syntax for changing Director filter parameters, enter help filter.

3.Repeat with the command of interest to view the syntax for all commands available from the CLI. For a complete description of all of the CLI commands, see Appendix B.

20

*** Confidential - DO NOT Distribute ***

Image 24

Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix a Appendix BAppendix C Filter parametersChapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools IBypass Switch Method In-line Monitoring of 10 Gigabit LinksExternal Network Tap method Power LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceInstall Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect Power to Director Connect the local CLI InterfaceConnect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management portLog into the CLI To log into the CLIConfigure Director using the CLI Change Director User Name and PasswordTo change the user name and password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Current config fileConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkConfigure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsNetwork Port 11 XFP Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersEnter filter list to view the pending filter list User interactions Filter capacityDaisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisSpecifications, DNM EnvironmentalCertifications Available ModelsAppendix B Command Line Interface Command Sub-Command Parameters Example and descriptionCommand may include Filter add and filter ins commandsFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=dropLoad myconfiguration-1 Filter listFilter running Filter syncSave myconfiguration-1 Show myconfiguration-1Passwd PingSysip commit Sysip ipaddr=192.168.1.2 netmask=255.255.0.0Sysip show TimeThis This command is only available at root level Command User showUser add name=bob pw=bob-pw priv=3 Is onlyFilter parameters Director Filter Parameters Qual Value Example DescriptionAppendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved