Net Optics none Sysip commit, Sysip ipaddr=192.168.1.2 netmask=255.255.0.0, Sysip show, Time

Page 50

 

 

 

 

 

 

 

 

 

 

 

Director

 

 

 

 

 

 

 

 

Command

Sub-Command

Parameters

Example and description

 

 

 

 

sysip

commit

 

sysip commit

 

 

 

 

Activates pending changes defined with sysip set

 

 

 

 

 

 

 

set

ipaddr=<address>

sysip ipaddr=192.168.1.2 netmask=255.255.0.0>

 

 

 

netmask=<netmask>

Parameters:

 

 

 

gw=<gateway>

<address> is the IP address (default: 192.168.1.2)

 

 

 

 

<netmask> is the netmask (default: 255.0.0.0)

 

 

 

 

<gateway> is the gateway IP address (default:

 

 

 

 

192.168.1.1)

 

 

 

 

 

Sets the Director IP address, netmask, and gateway

 

 

 

 

IP address; requires a sysip commit command to

 

 

 

 

activate the new settings

 

 

 

 

 

 

 

show

 

sysip show

 

 

 

 

Displays the current Director IP address information

 

 

 

 

time

 

<time>

time 13:02:00

 

 

 

 

Parameters:

 

 

 

 

<time> is hh:mm:ss

 

 

 

 

Sets the system time-of-day; if <time> is omitted, the

 

 

 

 

current time is displayed

 

 

 

 

upgrade

 

srvip=<svrip>

upgrade srvip=168.192.20.2 user=bob pw=bobpw

 

 

 

user=<username>

filename=image021108 2

 

 

 

pw=<passwd>

Parameter:

 

 

 

filename=<filename>

<svrip> is the IP address of the server that the

 

 

 

 

new image file is on

 

 

 

 

<username> is the user name needed for FTP

 

 

 

 

access to the server

 

 

 

 

<passwd> is the password needed for FTP

 

 

 

 

access to the server

 

 

 

 

<filename> is the name of the image file

 

 

 

 

Replaces the current system boot image with the

 

 

 

 

image in the specified file (see image command); all

 

 

 

 

parameters must be included and they must be in the

 

 

 

 

order shown

 

 

 

 

 

 

46

*** Confidential - DO NOT Distribute ***

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix C Appendix aAppendix B Filter parametersChapter Introduction Monitor port Filtering Key FeaturesEase of Use Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools External Network Tap method IBypass Switch MethodIn-line Monitoring of 10 Gigabit Links Monitor Port LEDs Power LEDsDirector Front Panel DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceRack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect Power to Director Connect the local CLI InterfaceTip Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control To connect the CLI for remote use over the Management portLog into the CLI To log into the CLITo change the user name and password Configure Director using the CLIChange Director User Name and Password To assign a new Manager IP address to Director To change the port modeAssign a New Manager IP Address Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Current config fileConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkConnect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsNetwork Port 11 XFP Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersEnter filter list to view the pending filter list User interactions Filter capacityDaisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisCertifications Specifications, DNMEnvironmental Available ModelsAppendix B Command Line Interface Command Sub-Command Parameters Example and descriptionFilter add ipv6=n inports=n1.1-n1.3 ip Command may includeFilter add and filter ins commands Src=10.1.1.1 action=dropFilter running Load myconfiguration-1Filter list Filter syncPasswd Save myconfiguration-1Show myconfiguration-1 PingSysip show Sysip commitSysip ipaddr=192.168.1.2 netmask=255.255.0.0 TimeUser add name=bob pw=bob-pw priv=3 This This command is only available at root level CommandUser show Is onlyFilter parameters Director Filter Parameters Qual Value Example DescriptionAppendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved
Top Page Image Contents