Net Optics none manual Filter list, Filter running, Filter sync, Help filter, History, Image, List

Page 48

Director

Command

Sub-Command

Parameters

 

Example and description

 

 

 

 

 

filter

list

ipv6=< y n >

 

filter list

(continued)

 

 

 

Parameters:

 

 

 

 

ipv6=y for IPv6 addressing; ipv6=n for IPv4 ad-

 

 

 

 

dressing (defaults to IPv4 if parameter is omitted)

 

 

 

 

Displays all pending filters (with filter IDs)

 

 

 

 

 

 

running

ipv6=< y n >

 

filter running

 

 

 

 

Parameters:

 

 

 

 

ipv6=y for IPv6 addressing; ipv6=n for IPv4 ad-

 

 

 

 

dressing (defaults to IPv4 if parameter is omitted)

 

 

 

 

Displays all active filters

 

 

 

 

 

 

sync

 

 

filter sync

 

 

 

 

Loads the pending filter list with a copy of the currently

 

 

 

 

active filters

 

 

 

 

 

help

 

<command>

 

help filter

 

 

 

 

Parameter:

 

 

 

 

<command> is any CLI command

 

 

 

 

Displays information about the specified CLI command;

 

 

 

 

if <command> is omitted, displays a list of all CLI

 

 

 

 

commands

 

 

 

 

 

history

 

 

 

history

 

 

 

 

Displays a numbered list of previously executed CLI

 

 

 

 

commands; any command can be executed directly

 

 

 

 

by entering the command number preceded by an

 

 

 

 

exclaimation point; up- and down-arrow keys can be

 

 

 

 

used to scroll through the command history buffeer

 

 

 

 

(see ! command)

 

 

 

 

 

image

 

< 1 2 >

 

image 2

 

 

 

 

Parameter:

 

 

 

 

Valid values are 1 and 2

 

 

 

 

Chooses which system image to boot from; if <n>

 

 

 

 

is omitted, the current system image information is

 

 

 

 

displayed (see upgrade command)

 

 

 

 

 

list

 

 

 

list

 

 

 

 

Shows a list of filenames of saved Director device

 

 

 

 

configurations (see save command)

 

 

 

 

 

load

 

<filename>*

 

load my_configuration-1

 

 

 

 

Parameters:

 

 

 

 

<filename> is the name of the file to load; a string;

 

 

 

 

do not include an extension

 

 

 

 

Loads a previously saved Director configuration (see

 

 

 

 

save command)

 

 

 

 

 

logout

 

 

 

logout

 

 

 

 

Exits the CLI shell (same as exit and quit)

 

 

 

 

 

module

show

 

 

module show

 

 

 

 

Lists information about Director hardware modules

 

 

 

 

including system serial number, DNM types, and

 

 

 

 

XFPs

 

 

 

 

 

 

 

 

 

 

 

 

 

44

 

*** Confidential - DO NOT Distribute ***

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix a Appendix BAppendix C Filter parametersChapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools IBypass Switch Method In-line Monitoring of 10 Gigabit LinksExternal Network Tap method Power LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceInstall Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect Power to Director Connect the local CLI InterfaceConnect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management portLog into the CLI To log into the CLIConfigure Director using the CLI Change Director User Name and PasswordTo change the user name and password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Current config fileConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkConfigure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsNetwork Port 11 XFP Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersEnter filter list to view the pending filter list User interactions Filter capacityDaisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisSpecifications, DNM EnvironmentalCertifications Available ModelsAppendix B Command Line Interface Command Sub-Command Parameters Example and descriptionCommand may include Filter add and filter ins commandsFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=dropLoad myconfiguration-1 Filter listFilter running Filter syncSave myconfiguration-1 Show myconfiguration-1Passwd PingSysip commit Sysip ipaddr=192.168.1.2 netmask=255.255.0.0Sysip show TimeThis This command is only available at root level Command User showUser add name=bob pw=bob-pw priv=3 Is onlyFilter parameters Director Filter Parameters Qual Value Example DescriptionAppendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved
Top Page Image Contents