Net Optics none manual View filters, Udp

Page 34

Director

Network Port 5

Protocol =

TCP

+ Monitor Port 1

Protocol =

UDP

lter add in_ports=n1.5 ip_proto=6 action=redir redir_ports=m.1 lter add in_ports=n1.5 ip_proto=17 action=redir redir_ports=m.1

Figure 29: Logical OR filter connection

View filters

To view a list of all pending filters, enter filter list. To view the active filters, enter filter running.

Net Optics> filter list

001 ip_src=00000000/ffffffff,ip_dst=00000000/ffffffff,ip_proto=0000

l4_src_port=0080,l4_dst_port=0000,vlan=0000,action=3 in_ports=01

redir_ports=13

002 ip_src=0a010101/ffffffff,ip_dst=00000000/ffffffff,ip_proto=0000

l4_src_port=0000,l4_dst_port=0000,vlan=0000,action=1 in_ports=00 05

003 ip_src=00000000/ffffffff,ip_dst=00000000/ffffffff,ip_proto=0000

l4_src_port=0000,l4_dst_port=0025,vlan=0000,action=3 in_ports=00

redir_ports=12 Net Optics>

Figure 30: Filter list command Tip!____________________________________________________________________________________________________

The ID numbers shown at the left of each filter in the filter list are the IDs that apply for filter del id=<id> and filter inc id=<id> commands, because all three commands act on the pending filter lsit. Do not use the IDs in a filter running list as the reference for filter del or filter ins commands.

________________________________________________________________________________________________________

30

*** Confidential - DO NOT Distribute ***

Image 34

Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix C Appendix aAppendix B Filter parametersChapter Introduction Monitor port Filtering Key FeaturesEase of Use Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools In-line Monitoring of 10 Gigabit Links IBypass Switch MethodExternal Network Tap method Monitor Port LEDs Power LEDsDirector Front Panel DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect Power to Director Connect the local CLI InterfaceTip Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control To connect the CLI for remote use over the Management portLog into the CLI To log into the CLIChange Director User Name and Password Configure Director using the CLITo change the user name and password To assign a new Manager IP address to Director To change the port modeAssign a New Manager IP Address Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Current config fileConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsNetwork Port 11 XFP Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersEnter filter list to view the pending filter list User interactions Filter capacityDaisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisCertifications Specifications, DNMEnvironmental Available ModelsAppendix B Command Line Interface Command Sub-Command Parameters Example and descriptionFilter add ipv6=n inports=n1.1-n1.3 ip Command may includeFilter add and filter ins commands Src=10.1.1.1 action=dropFilter running Load myconfiguration-1Filter list Filter syncPasswd Save myconfiguration-1Show myconfiguration-1 PingSysip show Sysip commitSysip ipaddr=192.168.1.2 netmask=255.255.0.0 TimeUser add name=bob pw=bob-pw priv=3 This This command is only available at root level CommandUser show Is onlyFilter parameters Director Filter Parameters Qual Value Example DescriptionAppendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved