Net Optics none manual USB port, Director Management

Page 9

Director

The inputs are divided into three groups: two DNMs plus the 10GbE ports. In-line DNM models support 6 in-line links, while Span DNM models support 12 Span ports. The diagram shows one in-line and one Span DNM. Both in‑line and Span DNMs are available with either Copper or SX Fiber interfaces. Different DNM types can be mixed in the same chassis, for example, one in-line Copper DNM and one Span Fiber DNM. The modules are hot-pluggable for easy serviceability. One or both DNM slots can be populated. The DNM slots are numbered 1 for the slot on the left and 2 for the slot on the right. If only one slot is populated, it should be slot 1.

The two configurable 10-Gigabit XFP ports are shown in the first two columns and last two rows of the diagram. The two dark black rows indicate that both ports are configured as Span inputs. The two dimmed columns indicate that the ports can alternately be configured as Monitor ports. The two ports may be configured as:

•Both Span

•Both Monitor

•One Span and one Monitor

USB port

A USB port located on the back is reserved for future functionality.

Director Management

Director can be configured and managed using a command-line interface (CLI) that will be familiar to most network administrators. The CLI runs locally over an RS-232 serial port or remotely over a secure SSH connection.

Net Optics GUI-based Compass management tools, which will be available soon, include:

•Web Manager—A Web-browser based tool to manage a single Director (at a time) from anywhere in the world

•System Manager—An SNMP platform-based tool to mange all the Director and other Net Optics iTap-enabled devices on your network

5

*** Confidential - DO NOT Distribute ***

Image 9

Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix B Appendix aAppendix C Filter parametersChapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure TechnologyDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools IBypass Switch Method In-line Monitoring of 10 Gigabit LinksExternal Network Tap method Director Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorBaud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management portTo log into the CLI Log into the CLIConfigure Director using the CLI Change Director User Name and PasswordTo change the user name and password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port ModesSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandCurrent config file Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksConfigure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsNetwork Port 11 XFP Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationEnter filter list to view the pending filter list Filter capacity User interactionsDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsEnvironmental Specifications, DNMCertifications Available ModelsCommand Sub-Command Parameters Example and description Appendix B Command Line InterfaceFilter add and filter ins commands Command may includeFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=dropFilter list Load myconfiguration-1Filter running Filter syncShow myconfiguration-1 Save myconfiguration-1Passwd PingSysip ipaddr=192.168.1.2 netmask=255.255.0.0 Sysip commitSysip show TimeUser show This This command is only available at root level CommandUser add name=bob pw=bob-pw priv=3 Is onlyDirector Filter Parameters Qual Value Example Description Filter parametersNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved