Net Optics none manual Connect Monitoring Tools to Director, Check the Installation

Page 28

Director

	1	2	3	4	5	In-Line
						In-Line
Director ™					A	10/100/1000
2					A	B

	A
1	B

6 7 8 9 10

www.netoptics.com

10	LINK	In-Line	A		B			A	B		A		B
100	ACT	GigaBit
1000		GigaBit
			1	2	3	4	5	6	7	8	9	10	11	12

Figure 21: In-line Network connections

Connect Monitoring Tools to Director

To connect a monitoring tool to Director, simply plug the appropriate cable into the desired 1 Gigabit or 10 Gigabit Monitor port and plug the other end into the monitoring tool. The Link LED for the port should illuminate after a short delay to indicate that a link has been established. Repeat for all desired monitoring tool connections.

Note:__________________________________________________________________________________________________

In the CLI, the Monitor ports are designated using the letter M followed by a dot, and then the port number. For example, the Monitor port on the upper left is m.1 and the Monitor port on the lower right is m.10.

________________________________________________________________________________________________________

Configure a Matrix Switch connection in Director

In order to monitor a network link, Director must be configured to copy the traffic from a Network or Span port to a Monitor port. A simple connection is described in this section, operating Director as a Matrix Switch. For more complex switching and filtering, see Chapter 3.

To monitor Network Port 1 (in DNM 1) on Monitor Port 2:

1.Enter filter add in_ports=n1.1 action=redir redir_ports=m.2. The switch connection is pending.

2.Enter filter commit. The switch connection is activated.

3.Verify that traffic present on Network Port 1 is visible on Monitor Port 2.

Check the Installation

You have connected Director to the network, monitoring tools, and power. It should now be functioning correctly. Check the status of the following:

•Check that at least one power LED is illuminated.

•Check the link status LEDs located on the front panel to verify that the links are connected.

•Verify that traffic is flowing through in-line connections to attached network devices.

•Verify that traffic present on Network port 1 is visible on Monitor Port 2.

24

*** Confidential - DO NOT Distribute ***

Image 28

Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix a Appendix BAppendix C Filter parametersChapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools In-line Monitoring of 10 Gigabit Links IBypass Switch MethodExternal Network Tap method Power LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect Power to Director Connect the local CLI InterfaceConnect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management portLog into the CLI To log into the CLIChange Director User Name and Password Configure Director using the CLITo change the user name and password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help information Using the CLI Command History Buffer Current config fileConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsNetwork Port 11 XFP Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersEnter filter list to view the pending filter list User interactions Filter capacityDaisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisSpecifications, DNM EnvironmentalCertifications Available ModelsAppendix B Command Line Interface Command Sub-Command Parameters Example and descriptionCommand may include Filter add and filter ins commandsFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=dropLoad myconfiguration-1 Filter listFilter running Filter syncSave myconfiguration-1 Show myconfiguration-1Passwd PingSysip commit Sysip ipaddr=192.168.1.2 netmask=255.255.0.0Sysip show TimeThis This command is only available at root level Command User showUser add name=bob pw=bob-pw priv=3 Is onlyFilter parameters Director Filter Parameters Qual Value Example DescriptionAppendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved