Net Optics none Passwd, Ping, Port set n1.1-n1.3 autoneg=on duplex=full, Port show, Quit, Restart

Page 49

Director

Command

Sub-Command

Parameters

Example and description

 

 

 

 

passwd

 

 

passwd

 

 

 

Interactively changes the password of the SSH user

 

 

 

account

 

 

 

 

ping

 

<address>*

ping 10.1.1.4

 

 

 

Parameters:

 

 

 

<address> is an IP address

 

 

 

Pings the specified IP address to check for connectivity

 

 

 

 

port

set

ports=<portlist>*

port set n1.1-n1.3 autoneg=on duplex=full

 

 

autoneg=< on off >

Parameters:

 

 

duplex=< full half >

<portllist> is a portlist

 

 

speed=< 10 100 1000 >

For other parameters, select a value from the

 

 

 

listed choices

 

 

 

For 10/100/100 Copper interface Network and Moni-

 

 

 

tor ports, enables or disables autonegotiation; selects

 

 

 

the duplex mode; and sets the fixed speed (10Mbps,

 

 

 

100Mbps, or 1000Mbps) if autonegotiation is off

 

 

 

 

 

show

 

port show

 

 

 

Displays the current port status and settings

 

 

 

 

quit

 

 

quit

 

 

 

Exits the CLI shell (same as exit and logout)

 

 

 

 

restart

 

 

restart

 

 

 

Reboots the Director device; also called warm boot;

 

 

 

similar to power-cycling the device; does not change

 

 

 

the configuration parameters or filters

 

 

 

 

save

 

 

save my_configuration-1

 

 

 

Parameters:

 

 

 

<filename> is the name of the file where the

 

 

 

configuration is saved; a string; do not include an

 

 

 

extension

 

 

 

Saves the Director device configuration to a file;

 

 

 

saved information includes port set-up and filters

 

 

 

 

show

 

<filename>*

show my_configuration-1

 

 

 

Parameters:

 

 

 

<filename> is the name of the file to display; a

 

 

 

string; do not include an extension

 

 

 

Displays the contents of the specified saved

 

 

 

configuration file (see save command)

 

 

 

 

stats

clear

ports=all<[portlist>

stats clear ports=all

 

 

 

Clears RMON statistics for the designated ports

 

 

 

 

 

show

ports=all<[portlist>

stats show ports=m.2,n1.4

 

 

 

Displays RMON statistics for the designated ports

 

 

 

 

45

*** Confidential - DO NOT Distribute ***

Image 49
Contents Smart Filtering Appliance Trademarks and Copyrights Contents Appendix B Appendix aAppendix C Filter parametersChapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure TechnologyDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links IBypass Switch MethodExternal Network Tap method Director Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorBaud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management portTo log into the CLI Log into the CLIChange Director User Name and Password Configure Director using the CLITo change the user name and password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port ModesSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandCurrent config file Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsNetwork Port 11 XFP Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationEnter filter list to view the pending filter list Filter capacity User interactionsDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsEnvironmental Specifications, DNMCertifications Available ModelsCommand Sub-Command Parameters Example and description Appendix B Command Line InterfaceFilter add and filter ins commands Command may includeFilter add ipv6=n inports=n1.1-n1.3 ip Src=10.1.1.1 action=dropFilter list Load myconfiguration-1Filter running Filter syncShow myconfiguration-1 Save myconfiguration-1Passwd PingSysip ipaddr=192.168.1.2 netmask=255.255.0.0 Sysip commitSysip show TimeUser show This This command is only available at root level CommandUser add name=bob pw=bob-pw priv=3 Is onlyDirector Filter Parameters Qual Value Example Description Filter parametersNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved