MRV Communications TS5000/XXX (TS5000G/XYZ/V**, TS5000/XYZ/V**, TS5000/ETH/V* Figures 1.5and

Page 23

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Selectors

Data Rate

Set the transmission rate of the transceiver (internal

(DIP Switch

(Toggles 1, 2, 3 and

clock).

DS1 Toggles)

4)

- Fast Ethernet: 1,2,3,4 OFF

---shown on

 

- ATM/OC3/STM1: 155 Mbps: 2,3,4 OFF, 1 ON

Figures 1.5and

 

- SMPTE 143 Mbps: 3,4 OFF, 1,2 ON

1.6

 

- E3: 34.368 Mbps 1,2,4 OFF, 3 ON

 

 

- T3: 44.736 Mbps: 2,4 OFF, 1,3 ON

 

 

- OC1/STM0: 51.840 Mbps: 1,4 OFF, 2,3 ON

 

 

- Customized 1 : 4 OFF, 1,2,3 ON

 

 

- Customized 2 : 1,3,4 OFF, 2 ON

 

 

- Open Protocol: 1, 2, 3 OFF, 4 ON.

Selectors

Mode Select

Set the Operating Mode

(DIP Switch

(Toggles 1, 2)

ALIGNMENT = Idle transmitted automatically

DS2 Toggles)

 

NORMAL = Signal received via the F/O port is

-- shown in

 

transmitted through the Airlink TX. Signal received

Figures 1.5 and

 

via the Airlink RX is transmitted through the F/O

1.6

 

TX.

 

 

LOOPBACK= Data received by the F/O RX is

 

 

directly returned through the F/O TX.

 

 

REMOTE LOOP = Loops the electrical RX to the

 

 

electrical TX and optical RX to the optical TX of the

 

 

remote unit.

 

 

 

 

Alignment Signal

ATTENUATION: The alignment signal is

 

Attenuation

attenuated (~20db) when the DIP switch toggle #3

 

(Toggle 3)

is moved to ON position.(to use when the

 

 

installation distance is less than 900m only for

 

 

alignment mode). Switch back to OFF position for

 

 

normal mode.

 

Laser Status

Turning off TXs lasers when the DIP switch toggle

 

(Toggle 4)

#4 is moved to ON

 

Fusion

This switch toggle enables working with MRV’s

 

(Toggle 5)

Fusion system (Built-in fusion option or switch

 

 

option). For additional information, see page 14.

 

 

Switch toggle 5 OFF: Fusion not Active (Disabled)

 

 

Switch toggle 5 ON: Fusion active (Enabled).

 

Window Heater

Used only with the heating option (To be specified

 

(Optional)

in the PO).

 

(Toggle 6)

Switch toggle 6 OFF: The heater is disabled

 

 

Switch toggle 5 ON: The heater is enabled.

 

 

The heating will start operating only if one of the

 

 

following conditions is present: or the temperature is

 

 

lower than 15oC; or the humidity level in the air is

 

 

above 80%. There is a controller with a thermostat

 

 

inside the TereScope, which controls the heating in

 

 

accordance with the above conditions.

 

IP address set up

When the Switch toggle is on OFF position, the

 

(Toggle 8)

TereScope’s IP address is the default one (shown on

 

 

the back panel label: 10.0.0.101). To set a new IP

 

 

address, please refer to the “IP address setting

 

 

procedure for TereScope management card” file in

 

 

the Manuals CD. The new IP address is valid only

 

 

after the TereScope is powered off and on.

 

Control Mode

When the Dip Switch toggle #10 is on OFF

 

(Toggle 10)

position, the TereScope is in the HARDWARE

 

 

mode, i.e. the TereScope is controlled only by the

 

 

TereScope itself by means of the switches on its

 

 

back panel.

 

 

When the Dip Switch toggle is on ON position, the

 

 

TereScope is in the SOFTWARE mode i.e. the

 

 

TereScope is controlled by the management

 

 

Software and various functions can be activated by

 

 

means of this management Software.

 

 

 

12

Image 23
Contents InstallationManual Installation Manual Table of Contents Page Digital Readout vs. Distance Product specificationsTereScope Bench Test Procedure Power Supply ReplacementCE Mark StandardsStandards Compliance FCC NoticeTrademarks MRV Laser Safety CertificationOther Standards DisclaimerAboutthisInstallationManual Line Power Power Cord SafetyRequirementsBefore Installing When InstallingServicing Introduction Carefully Read the Entire Manual Before InstallingModels Part Number Description TheProductModels TS5000/M3C/V1S Using the Part Number for OrderingGeneral Description FrontBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option RF = 2-10 Mbps Or 100Mbps Fusion Operation ModeRF Transceiver IR = 100 Mbps or 1.25Gbps7b TS & Fusion FusionTS5000/ETH Model Back Panel TS5000/ETH Ethernet SystemSelectors DIP TS5000-4U1 Model Back Panel TS5000/4U1 4E1 or 4T1 SystemTo D Dip switch settingHeating Loop and Remote Loop Operation ModeWhen turning off the Master, the Slave exits Loop state RSM Monitoring and Management optionsManagement Dry contactCopper Connection Typical ConnectionFiber Connection Location & Range SiteSurveyLine of Sight OrientationPrefer Avoid Pay attention to Acceptable Mounting Unacceptable Mounting Mounting Environment & StabilityWall Mounting using JMP and JMB Transmitting through a Window 10 Extended Wall Mounting using JMP and MO62CInfrastructure PowerData/Signal Cabling Handle the Fibers Very Carefully Compatibility Testing equipmentSetup BenchTestTS5000/155&TS5000/155-F TS5000/4U1 Dip-switch SetupBench test Test ConfigurationsIR link Display and Results IndicatorsReceived power Optical PowerAIR RX 1000 Snmp Management Setting and Operation100 Description InstallationAccessories Do not touch this screw K Alignment Knobs Installer Tool Kit JITK-8Mounting Accessories11b Locking the screws between TS and alignment device Do not open Screws GMounting on the floor Particular Figure Cases/TechniquesPowering on the TereScope AimingProcedureScrews D & L are closed Transceiver Alignment− Coarse Alignment − Fine Alignment Swing BaseBeam cross section at the shot distance ClosedJ-R-3 Procedure Before Closing the Rear Door An example of an installation form is shown in Appendix HClosing the rear door InstallationCompletionVisual Inspection 13 Mounted TS5000 Left View Periodic Visits MaintenanceTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Packing box contains AppendixcAppendixd Tool Case Where to usePoints to Remember IntroductionInterference Bench Test for TS700 and TS800 series with JAH-L Figure E.2b Bench Test setup drawing for 10 TS modelFigure E.5 Bench test with TereScopes elevated Page Wind Force = 0.79 x Wind Speed2 x Area of Surface TS Device Momentary ExtendedFSO Chaining AppendixGUse the indoor switch in building C for the chaining SwitchFSO products & Chaining Product series No of chained links Sketch of the area Client / Dealer detailsApplication details Site survey Installation System failure Appendixi TS5000/155 and TS4000/155 enhancements Appendixj

TS5000/ETH/V*, TS5000/XYZ/V**, TS5000/XXX (TS5000G/XYZ/V**, TS5000/4U1/V*) specifications

MRV Communications has established a strong reputation in the networking industry, known for delivering innovative solutions that enhance the performance and reliability of communication systems. One of their standout product lines is the TS5000 series, which includes models such as TS5000/4U1/V*, TS5000/XXX, TS5000G/XYZ/V**, TS5000/XYZ/V**, and TS5000/ETH/V*. These devices are engineered to meet the growing demands of modern networks, providing a range of features that cater to various connectivity needs.

The TS5000 series is designed with versatility in mind, accommodating multiple deployment scenarios in both enterprise and service provider environments. One of the key features of the TS5000 models is their comprehensive support for multi-service operations. This means they can seamlessly handle different types of traffic including voice, video, and data, making them ideal for organizations that require robust communication solutions.

Incorporating state-of-the-art technologies, the TS5000 series supports various networking protocols and standards. This interoperability ensures compatibility with a wide array of existing network setups, allowing for easier integration and reduced overhead costs. The series utilizes advanced Ethernet technologies that enhance bandwidth efficiency and support high-speed data transfers.

Reliability is another hallmark of the TS5000 series. These devices are built with redundancy in mind, featuring hot-swappable components and failover capabilities that minimize downtime. This is critical for organizations that cannot afford interruptions in service, such as those in the finance or healthcare sectors.

Security is also a priority in the design of the TS5000 series. With built-in encryption and secure access controls, these devices help organizations protect sensitive data from cyber threats. The management interface is designed for ease of use, allowing IT teams to monitor and configure the system effortlessly.

Another notable characteristic of the TS5000 series is its scalability. Organizations can start with a basic configuration and expand their network capabilities as their needs grow. This flexibility makes the TS5000 an ideal choice for businesses aiming for future growth.

In summary, the MRV Communications TS5000 series represents a comprehensive solution for today's networking challenges. With its focus on multi-service support, advanced technology, reliability, security, and scalability, the TS5000 models are well-equipped to serve the demands of diverse environments, making them a valuable addition to any network infrastructure.