MRV Communications TS5000/XYZ/V**, TS5000/ETH/V*, TS5000/4U1/V*) installation manual Indicators

Page 24

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Indicators

Air RX Flag LED

Green LED indicates data received by the Airlink

(7-segment

 

receiver. Turns ON at the threshold level.

display and

Air RX Sync LED

Yellow LED. Turns ON if the rate of the received

LEDs)

 

Data matches the Data Rate set on the Data Rate

 

 

DIP switch.

 

F/O Main, RX Flag

Upper green LED indicates Data received by the

 

LED

Fiber Optic receiver. Turns ON at the threshold

 

 

level.

 

F/O Main, RX Sync

Lower green LED. Turns ON if the rate of the

 

LED

received Data matches the Data Rate set on the

 

 

Data Rate DIP switch.

 

F/O Redundant, RX

Upper green LED indicates Data received by the

 

Flag LED

Fiber Optic receiver. Turns ON at the threshold

 

(Optional)

level.

 

 

 

 

F/O Redundant, RX

Lower green LED. Turns ON if the Fusion is

 

Sync LED

active and there is synchronization with the

 

(Optional)

received Data.

 

 

 

 

Optical Power 7-

Digital readout indicates the Optical Power level

 

segment display

received by the Airlink receiver.

 

 

 

 

Alignment LED

Yellow LED. Turns ON if the Alignment

 

 

Operating Mode is selected.

 

Loop LED

Yellow LED. Turns ON in LOOPBACK mode.

 

 

Flashing in Remote Loop mode.

 

Fusion LED

Yellow LED. Turns ON if the Fusion mode is

 

 

enabled.

 

 

Flashing when the Fusion (radio back-up system) is

 

 

active.

 

Heating LED

Yellow LED. Turns ON if the heating mode is

 

 

selected (Heating is enabled).

 

SW Mode LED

Red LED. Turns ON if the SW Mode

 

 

(SOFTWARE) Operating Mode is selected.

 

Lasers status LEDs

There are 3 LEDs – L1, L2, L3 indicating if the

 

 

lasers are switched on or off. If the LED is

 

 

switched off, the laser is switched off. If the LED is

 

 

switched ON, the laser is switched ON.

 

 

When the DIP switch toggle #3 is moved to ON

 

 

position the LED L1 and its corresponding laser

 

 

will turn off

 

PS1

Green LED. Turns ON when main power supply is

 

 

active

 

PS2

Green LED. Turns ON when redundant power

 

 

supply is active

 

Heater ON

Green LED. Turns ON when the heating of the

 

 

front window is active.

 

 

The heating will start operating only if one of the

 

 

following conditions is present: or the temperature

 

 

is lower than 15oC; or the humidity level in the air is

 

 

above 80%. There is a controller with a thermostat

 

 

inside the TereScope, which controls the heating in

 

 

accordance with the above conditions. (The heating

 

 

option is not standard, and exists only if purchased)

 

 

 

 

Management TX

Flashing when the RSM-SNMP is connected and

 

 

the TereScope is transmitting management Data.

 

 

(There is no Link indication)

 

Management RX

Flashing when the RSM-SNMP is connected and

 

 

the TereScope is receiving management Data.

 

 

(There is no Link indication)

 

 

 

13

Image 24
Contents InstallationManual Installation Manual Table of Contents Page Product specifications TereScope Bench Test ProcedurePower Supply Replacement Digital Readout vs. DistanceStandards Standards ComplianceFCC Notice CE MarkMRV Laser Safety Certification Other StandardsDisclaimer TrademarksAboutthisInstallationManual SafetyRequirements Before InstallingWhen Installing Line Power Power CordServicing Carefully Read the Entire Manual Before Installing IntroductionTheProduct ModelsModels Part Number Description Using the Part Number for Ordering TS5000/M3C/V1SFront General DescriptionBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option Fusion Operation Mode RF TransceiverIR = 100 Mbps or 1.25Gbps RF = 2-10 Mbps Or 100MbpsFusion 7b TS & FusionTS5000/ETH Ethernet System TS5000/ETH Model Back PanelSelectors DIP TS5000/4U1 4E1 or 4T1 System TS5000-4U1 Model Back PanelDip switch setting To DLoop and Remote Loop Operation Mode When turning off the Master, the Slave exits Loop stateHeating Monitoring and Management options ManagementDry contact RSMTypical Connection Fiber ConnectionCopper Connection SiteSurvey Line of SightOrientation Location & RangePrefer Avoid Pay attention to Acceptable Mounting Mounting Environment & Stability Unacceptable MountingWall Mounting using JMP and JMB 10 Extended Wall Mounting using JMP and MO62C Transmitting through a WindowPower Data/Signal CablingInfrastructure Handle the Fibers Very Carefully Testing equipment SetupBenchTest CompatibilityTS5000/155&TS5000/155-F Dip-switch Setup TS5000/4U1Test Configurations Bench testIR link Indicators Received powerOptical Power Display and ResultsAIR RX Snmp Management Setting and Operation 1001000 Installation AccessoriesDescription Do not touch this screw K Installer Tool Kit JITK-8 Alignment KnobsAccessories MountingDo not open Screws G 11b Locking the screws between TS and alignment deviceParticular Figure Cases/Techniques Mounting on the floorAimingProcedure Powering on the TereScopeTransceiver Alignment − Coarse Alignment − Fine AlignmentSwing Base Screws D & L are closedClosed J-R-3Beam cross section at the shot distance Procedure An example of an installation form is shown in Appendix H Before Closing the Rear DoorInstallationCompletion Visual InspectionClosing the rear door 13 Mounted TS5000 Left View Maintenance Periodic VisitsTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Appendixc Packing box containsAppendixd Where to use Tool CaseIntroduction Points to RememberInterference Figure E.2b Bench Test setup drawing for 10 TS model Bench Test for TS700 and TS800 series with JAH-LFigure E.5 Bench test with TereScopes elevated Page TS Device Momentary Extended Wind Force = 0.79 x Wind Speed2 x Area of SurfaceAppendixG FSO ChainingSwitch Use the indoor switch in building C for the chainingFSO products & Chaining Product series No of chained links Client / Dealer details Application detailsSketch of the area Site survey Installation System failure Appendixi Appendixj TS5000/155 and TS4000/155 enhancements

TS5000/ETH/V*, TS5000/XYZ/V**, TS5000/XXX (TS5000G/XYZ/V**, TS5000/4U1/V*) specifications

MRV Communications has established a strong reputation in the networking industry, known for delivering innovative solutions that enhance the performance and reliability of communication systems. One of their standout product lines is the TS5000 series, which includes models such as TS5000/4U1/V*, TS5000/XXX, TS5000G/XYZ/V**, TS5000/XYZ/V**, and TS5000/ETH/V*. These devices are engineered to meet the growing demands of modern networks, providing a range of features that cater to various connectivity needs.

The TS5000 series is designed with versatility in mind, accommodating multiple deployment scenarios in both enterprise and service provider environments. One of the key features of the TS5000 models is their comprehensive support for multi-service operations. This means they can seamlessly handle different types of traffic including voice, video, and data, making them ideal for organizations that require robust communication solutions.

Incorporating state-of-the-art technologies, the TS5000 series supports various networking protocols and standards. This interoperability ensures compatibility with a wide array of existing network setups, allowing for easier integration and reduced overhead costs. The series utilizes advanced Ethernet technologies that enhance bandwidth efficiency and support high-speed data transfers.

Reliability is another hallmark of the TS5000 series. These devices are built with redundancy in mind, featuring hot-swappable components and failover capabilities that minimize downtime. This is critical for organizations that cannot afford interruptions in service, such as those in the finance or healthcare sectors.

Security is also a priority in the design of the TS5000 series. With built-in encryption and secure access controls, these devices help organizations protect sensitive data from cyber threats. The management interface is designed for ease of use, allowing IT teams to monitor and configure the system effortlessly.

Another notable characteristic of the TS5000 series is its scalability. Organizations can start with a basic configuration and expand their network capabilities as their needs grow. This flexibility makes the TS5000 an ideal choice for businesses aiming for future growth.

In summary, the MRV Communications TS5000 series represents a comprehensive solution for today's networking challenges. With its focus on multi-service support, advanced technology, reliability, security, and scalability, the TS5000 models are well-equipped to serve the demands of diverse environments, making them a valuable addition to any network infrastructure.