MRV Communications TS5000/XXX (TS5000G/XYZ/V** BenchTest, Compatibility, Testing equipment, Setup

Page 43

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Chapter

4

BenchTest

It is always easier and more convenient to locate a failure and solve a problem in a lab on a bench than on a roof under bad conditions. It is then strongly recommended, as the circumstances allow it, to perform a bench test with all the modules prior to the installation in order to check the equipment compatibilityandtovalidatetheconfiguration.

See Unpacking Instructions in Appendix C.

1-TS5000/G &TS5000/G-F

Compatibility

Peripheral equipment

Check the operating of the peripheral equipment connecting them through cables (see Configuration 1 below).

Interfaces

Check the specifications compatibility (type, wavelength, receiver range, output power, data rate) between the TereScope and the peripheral equipment interfaces.

Testing equipment

Chose an appropriate BER (Bit Error Rate) tester for checking the physical link quality. A portable one is preferred for convenient use in the field.

For example: A smartbit Giga Ethernet tester.

A ping test or a file transfer between two workstations - connected to the networking equipment - is useful and easy to implement for testing the performance of the whole configuration.

Setup

Dip-switch

Set all the DIP switch toggles to the OFF position for normal operation.

32

Page 42 Page 44
Image 43
Page 42 Page 44
Contents InstallationManual Installation Manual Table of Contents Page Digital Readout vs. Distance Product specificationsTereScope Bench Test Procedure Power Supply ReplacementCE Mark StandardsStandards Compliance FCC NoticeTrademarks MRV Laser Safety CertificationOther Standards DisclaimerAboutthisInstallationManual Line Power Power Cord SafetyRequirementsBefore Installing When InstallingServicing Introduction Carefully Read the Entire Manual Before InstallingModels TheProductModels Part Number Description TS5000/M3C/V1S Using the Part Number for OrderingGeneral Description FrontBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option RF = 2-10 Mbps Or 100Mbps Fusion Operation ModeRF Transceiver IR = 100 Mbps or 1.25Gbps7b TS & Fusion FusionTS5000/ETH Model Back Panel TS5000/ETH Ethernet SystemSelectors DIP TS5000-4U1 Model Back Panel TS5000/4U1 4E1 or 4T1 SystemTo D Dip switch settingWhen turning off the Master, the Slave exits Loop state Loop and Remote Loop Operation ModeHeating RSM Monitoring and Management optionsManagement Dry contactFiber Connection Typical ConnectionCopper Connection Location & Range SiteSurveyLine of Sight OrientationPrefer Avoid Pay attention to Acceptable Mounting Unacceptable Mounting Mounting Environment & StabilityWall Mounting using JMP and JMB Transmitting through a Window 10 Extended Wall Mounting using JMP and MO62CData/Signal Cabling PowerInfrastructure Handle the Fibers Very Carefully Compatibility Testing equipmentSetup BenchTestTS5000/155&TS5000/155-F TS5000/4U1 Dip-switch SetupBench test Test ConfigurationsIR link Display and Results IndicatorsReceived power Optical PowerAIR RX 100 Snmp Management Setting and Operation1000 Accessories InstallationDescription Do not touch this screw K Alignment Knobs Installer Tool Kit JITK-8Mounting Accessories11b Locking the screws between TS and alignment device Do not open Screws GMounting on the floor Particular Figure Cases/TechniquesPowering on the TereScope AimingProcedureScrews D & L are closed Transceiver Alignment− Coarse Alignment − Fine Alignment Swing BaseJ-R-3 ClosedBeam cross section at the shot distance Procedure Before Closing the Rear Door An example of an installation form is shown in Appendix HVisual Inspection InstallationCompletionClosing the rear door 13 Mounted TS5000 Left View Periodic Visits MaintenanceTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Packing box contains AppendixcAppendixd Tool Case Where to usePoints to Remember IntroductionInterference Bench Test for TS700 and TS800 series with JAH-L Figure E.2b Bench Test setup drawing for 10 TS modelFigure E.5 Bench test with TereScopes elevated Page Wind Force = 0.79 x Wind Speed2 x Area of Surface TS Device Momentary ExtendedFSO Chaining AppendixGUse the indoor switch in building C for the chaining SwitchFSO products & Chaining Product series No of chained links Application details Client / Dealer detailsSketch of the area Site survey Installation System failure Appendixi TS5000/155 and TS4000/155 enhancements Appendixj

TS5000/ETH/V*, TS5000/XYZ/V**, TS5000/XXX (TS5000G/XYZ/V**, TS5000/4U1/V*) specifications

MRV Communications has established a strong reputation in the networking industry, known for delivering innovative solutions that enhance the performance and reliability of communication systems. One of their standout product lines is the TS5000 series, which includes models such as TS5000/4U1/V*, TS5000/XXX, TS5000G/XYZ/V**, TS5000/XYZ/V**, and TS5000/ETH/V*. These devices are engineered to meet the growing demands of modern networks, providing a range of features that cater to various connectivity needs.

The TS5000 series is designed with versatility in mind, accommodating multiple deployment scenarios in both enterprise and service provider environments. One of the key features of the TS5000 models is their comprehensive support for multi-service operations. This means they can seamlessly handle different types of traffic including voice, video, and data, making them ideal for organizations that require robust communication solutions.

Incorporating state-of-the-art technologies, the TS5000 series supports various networking protocols and standards. This interoperability ensures compatibility with a wide array of existing network setups, allowing for easier integration and reduced overhead costs. The series utilizes advanced Ethernet technologies that enhance bandwidth efficiency and support high-speed data transfers.

Reliability is another hallmark of the TS5000 series. These devices are built with redundancy in mind, featuring hot-swappable components and failover capabilities that minimize downtime. This is critical for organizations that cannot afford interruptions in service, such as those in the finance or healthcare sectors.

Security is also a priority in the design of the TS5000 series. With built-in encryption and secure access controls, these devices help organizations protect sensitive data from cyber threats. The management interface is designed for ease of use, allowing IT teams to monitor and configure the system effortlessly.

Another notable characteristic of the TS5000 series is its scalability. Organizations can start with a basic configuration and expand their network capabilities as their needs grow. This flexibility makes the TS5000 an ideal choice for businesses aiming for future growth.

In summary, the MRV Communications TS5000 series represents a comprehensive solution for today's networking challenges. With its focus on multi-service support, advanced technology, reliability, security, and scalability, the TS5000 models are well-equipped to serve the demands of diverse environments, making them a valuable addition to any network infrastructure.
Top Page Image Contents