MRV Communications TS5000/XXX (TS5000G/XYZ/V, TS5000/XYZ/V, TS5000/ETH/V, TS5000/4U1/V)

Page 67

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

TS5000/ETH

Part Number

Model

Standard P.N

Application / Data Protocol

Performance

Transmitter

Receiver

Interface

Power Supply

Rate

Range (1) @ 3dB/km @ 5dB/km @ 10dB/km @ 17dB/km @ 30dB/km

Minimum Range

Bit Error Rate

MTBF

Light source

Wavelength

Total Output power

Beam divergence

Detector

Field of view

Sensitivity

Type

Connectors

Cable

TS5000/ETH/V*

TS5000/ETH

TS5000/ETH/VS

Ethernet (10 Mbps)

10Mbps

6700 m

5000 m

3200 m

2170 m

1400 m

400 m

Less than 1E-9 (unfaded)

10years 3 x Lasers

830-860 nm

85mW

2mrad

APD

2mrad

-55 dBm

Copper 10BaseT

RJ45

STP

Factory set: 100-240 VAC @ 50/60 Hz or 35-60 VDC (V3 Version)

(30 W)

Environmental Information

Mechanical Design

Diagnostics Indicators and Selectors

Operating Temp.

Storage Temp.

Humidity

Housing

Eye safety Class

Dimensions [mm]

Weight Unit Accessories

Modularity

Indicators

Selectors

Dry Contact

Management

-30 °C to +50 °C

-50 °C to +70 °C

95% non-condensing

Weatherproof – IP 66

1M

790 X 390 X 556 (AD-5000: 250x353x432)

14kg 21.5kg

Modular Power supply

Airlink: Flag, Data. 10Base-T: Flag, Data.

Receive Signal Strength (Digital Display),

Lasers status (3 LEDs)

IP address setting

One pair of Pins of the main RJ45 connector can be used for dry contact purposes, for Airlink flag alarm

SNMP Protocol – Built-in

56

Image 67

Contents InstallationManual Installation Manual Table of Contents Page Digital Readout vs. Distance Product specificationsTereScope Bench Test Procedure Power Supply ReplacementCE Mark StandardsStandards Compliance FCC NoticeTrademarks MRV Laser Safety CertificationOther Standards DisclaimerAboutthisInstallationManual Line Power Power Cord SafetyRequirementsBefore Installing When InstallingServicing Introduction Carefully Read the Entire Manual Before InstallingModels TheProductModels Part Number Description TS5000/M3C/V1S Using the Part Number for OrderingGeneral Description FrontBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option RF = 2-10 Mbps Or 100Mbps Fusion Operation ModeRF Transceiver IR = 100 Mbps or 1.25Gbps7b TS & Fusion FusionTS5000/ETH Model Back Panel TS5000/ETH Ethernet SystemSelectors DIP TS5000-4U1 Model Back Panel TS5000/4U1 4E1 or 4T1 SystemTo D Dip switch settingWhen turning off the Master, the Slave exits Loop state Loop and Remote Loop Operation ModeHeating RSM Monitoring and Management optionsManagement Dry contactFiber Connection Typical ConnectionCopper Connection Location & Range SiteSurveyLine of Sight OrientationPrefer Avoid Pay attention to Acceptable Mounting Unacceptable Mounting Mounting Environment & StabilityWall Mounting using JMP and JMB Transmitting through a Window 10 Extended Wall Mounting using JMP and MO62CData/Signal Cabling PowerInfrastructure Handle the Fibers Very Carefully Compatibility Testing equipmentSetup BenchTestTS5000/155&TS5000/155-F TS5000/4U1 Dip-switch SetupBench test Test ConfigurationsIR link Display and Results IndicatorsReceived power Optical PowerAIR RX 100 Snmp Management Setting and Operation1000 Accessories InstallationDescription Do not touch this screw K Alignment Knobs Installer Tool Kit JITK-8Mounting Accessories11b Locking the screws between TS and alignment device Do not open Screws GMounting on the floor Particular Figure Cases/TechniquesPowering on the TereScope AimingProcedureScrews D & L are closed Transceiver Alignment− Coarse Alignment − Fine Alignment Swing BaseJ-R-3 ClosedBeam cross section at the shot distance Procedure Before Closing the Rear Door An example of an installation form is shown in Appendix HVisual Inspection InstallationCompletionClosing the rear door 13 Mounted TS5000 Left View Periodic Visits MaintenanceTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Packing box contains AppendixcAppendixd Tool Case Where to usePoints to Remember IntroductionInterference Bench Test for TS700 and TS800 series with JAH-L Figure E.2b Bench Test setup drawing for 10 TS modelFigure E.5 Bench test with TereScopes elevated Page Wind Force = 0.79 x Wind Speed2 x Area of Surface TS Device Momentary ExtendedFSO Chaining AppendixGUse the indoor switch in building C for the chaining SwitchFSO products & Chaining Product series No of chained links Application details Client / Dealer detailsSketch of the area Site survey Installation System failure Appendixi TS5000/155 and TS4000/155 enhancements Appendixj