MRV Communications TS5000/XXX (TS5000G/XYZ/V** Installation, Accessories, Description

Page 51

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Chapter

5

Installation

Thischapterdealswiththemountingofthehardwareandthe unit onthesite(seeAppendixDfortherequiredmaterial).

See Unpacking Instructions in Appendix C.

CAUTION: Unit to be mounted in horizontal position only. Max angle 45o

Accessories

The standard mounting accessories are supplied with the transceiver in a kit. They are designed for typical mounting on horizontal and vertical surfaces.

Description

The accessories kit (supplied by MRV) consists of :

oThe Mounting Plate (JMP-8)

oThe Alignment Device (AD-5000) o The Installer Tool Kit (JITK-8)

The JMP-8 is used for mounting the transceiver on the support surface. (i.e. to a horizontal concrete surface/plate only) the JMP-8 is not fit to the MRV standard mounting brackets, if needed to mount it on MRV standard mounting brackets, attach the AD5000 base plate directly to the mounting bracket top plate without the JMP-8

The AD-5000 allows the aiming of the two units making the link (see chapter 6)

JMP-8 Mounting Plate (dimensions in mm)

A: Screw for grounding

Dimensions in mm

Figure 5.1a: JMP-8

Figure 5.1b: JMP-8

40

Image 51

Contents InstallationManual Installation Manual Table of Contents Page Digital Readout vs. Distance Product specificationsTereScope Bench Test Procedure Power Supply ReplacementCE Mark StandardsStandards Compliance FCC NoticeTrademarks MRV Laser Safety CertificationOther Standards DisclaimerAboutthisInstallationManual Line Power Power Cord SafetyRequirementsBefore Installing When InstallingServicing Introduction Carefully Read the Entire Manual Before InstallingTheProduct ModelsModels Part Number Description TS5000/M3C/V1S Using the Part Number for OrderingGeneral Description FrontBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option RF = 2-10 Mbps Or 100Mbps Fusion Operation ModeRF Transceiver IR = 100 Mbps or 1.25Gbps7b TS & Fusion FusionTS5000/ETH Model Back Panel TS5000/ETH Ethernet SystemSelectors DIP TS5000-4U1 Model Back Panel TS5000/4U1 4E1 or 4T1 SystemTo D Dip switch settingLoop and Remote Loop Operation Mode When turning off the Master, the Slave exits Loop stateHeating RSM Monitoring and Management optionsManagement Dry contactTypical Connection Fiber ConnectionCopper Connection Location & Range SiteSurveyLine of Sight OrientationPrefer Avoid Pay attention to Acceptable Mounting Unacceptable Mounting Mounting Environment & StabilityWall Mounting using JMP and JMB Transmitting through a Window 10 Extended Wall Mounting using JMP and MO62CPower Data/Signal CablingInfrastructure Handle the Fibers Very Carefully Compatibility Testing equipmentSetup BenchTestTS5000/155&TS5000/155-F TS5000/4U1 Dip-switch SetupBench test Test ConfigurationsIR link Display and Results Indicators Received power Optical PowerAIR RX Snmp Management Setting and Operation 1001000 Installation AccessoriesDescription Do not touch this screw K Alignment Knobs Installer Tool Kit JITK-8Mounting Accessories11b Locking the screws between TS and alignment device Do not open Screws GMounting on the floor Particular Figure Cases/TechniquesPowering on the TereScope AimingProcedureScrews D & L are closed Transceiver Alignment− Coarse Alignment − Fine Alignment Swing BaseClosed J-R-3Beam cross section at the shot distance Procedure Before Closing the Rear Door An example of an installation form is shown in Appendix HInstallationCompletion Visual InspectionClosing the rear door 13 Mounted TS5000 Left View Periodic Visits MaintenanceTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Packing box contains AppendixcAppendixd Tool Case Where to usePoints to Remember IntroductionInterference Bench Test for TS700 and TS800 series with JAH-L Figure E.2b Bench Test setup drawing for 10 TS modelFigure E.5 Bench test with TereScopes elevated Page Wind Force = 0.79 x Wind Speed2 x Area of Surface TS Device Momentary ExtendedFSO Chaining AppendixGUse the indoor switch in building C for the chaining SwitchFSO products & Chaining Product series No of chained links Client / Dealer details Application detailsSketch of the area Site survey Installation System failure Appendixi TS5000/155 and TS4000/155 enhancements Appendixj