MRV Communications TS5000/ETH/V*, TS5000/XYZ/V**, TS5000/4U1/V*) installation manual Air Rx

Page 49

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Notes

1 - In case the tested TereScope has a Fusion option, the LEDs of the redundant F/O should be switched off if the backup is not connected.

2 – TX LED Flashing when the RSM-SNMP is connected and the TereScope is transmitting management Data. (There is no Link indication)

RX LED Flashing when the RSM-SNMP is connected and the TereScope is receiving management Data. (There is no Link indication)

3 - This LED switches ON, when the fusion option is enabled. It starts blinking, when fusion is active, i.e. when the IR link stops operating and the back-up link becomes active.

4 - This LED switches ON only when there is a heating option. The heating is activated by moving the DIP Switch toggle # 5 to ON position.

5 - When the RSM-SNMP is connected and you choose to control the TereScope by software (Megavision), move the DIP Switch #10 to ON position and this LED will switch ON.

2. Received power

100 < OPTICAL POWER < 1000

Expected Results

The BER must be less than 10E-12 (10-12) for on-going tests and error-free for short tests.

The PING test and file transfer procedure should not notify any TIME OUT alarm or last too long time compared to cabling connection.

3.TS5000/ETH

Proper Display

1.Indicators

Indicator →

AIR RX

10 Base-T

Lasers Status

Position ↓

Link

Data

Link

Data

L1 to L3

ON

x

 

x

 

x

OFF

 

 

 

 

 

Blinking

 

x

 

x

 

Table 10: Indicators

2. Received power

100 < OPTICAL POWER < 1000

Expected Results

The BER must be less than 1E-9 for lasting tests and display NO ERRORS for brief ones.

The PING test and file transfer procedure should not notify any TIME OUT alarm or last too long time compared to cabling connection.

38

Image 49
Contents InstallationManual Installation Manual Table of Contents Page TereScope Bench Test Procedure Product specificationsPower Supply Replacement Digital Readout vs. DistanceStandards Compliance StandardsFCC Notice CE MarkOther Standards MRV Laser Safety CertificationDisclaimer TrademarksAboutthisInstallationManual Before Installing SafetyRequirementsWhen Installing Line Power Power CordServicing Introduction Carefully Read the Entire Manual Before InstallingModels TheProductModels Part Number Description TS5000/M3C/V1S Using the Part Number for OrderingGeneral Description FrontBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option RF Transceiver Fusion Operation ModeIR = 100 Mbps or 1.25Gbps RF = 2-10 Mbps Or 100Mbps7b TS & Fusion FusionTS5000/ETH Model Back Panel TS5000/ETH Ethernet SystemSelectors DIP TS5000-4U1 Model Back Panel TS5000/4U1 4E1 or 4T1 SystemTo D Dip switch settingWhen turning off the Master, the Slave exits Loop state Loop and Remote Loop Operation ModeHeating Management Monitoring and Management optionsDry contact RSMFiber Connection Typical ConnectionCopper Connection Line of Sight SiteSurveyOrientation Location & RangePrefer Avoid Pay attention to Acceptable Mounting Unacceptable Mounting Mounting Environment & StabilityWall Mounting using JMP and JMB Transmitting through a Window 10 Extended Wall Mounting using JMP and MO62CData/Signal Cabling PowerInfrastructure Handle the Fibers Very Carefully Setup Testing equipmentBenchTest CompatibilityTS5000/155&TS5000/155-F TS5000/4U1 Dip-switch SetupBench test Test ConfigurationsIR link Received power IndicatorsOptical Power Display and ResultsAIR RX 100 Snmp Management Setting and Operation1000 Accessories InstallationDescription Do not touch this screw K Alignment Knobs Installer Tool Kit JITK-8Mounting Accessories11b Locking the screws between TS and alignment device Do not open Screws GMounting on the floor Particular Figure Cases/TechniquesPowering on the TereScope AimingProcedure− Coarse Alignment − Fine Alignment Transceiver AlignmentSwing Base Screws D & L are closedJ-R-3 ClosedBeam cross section at the shot distance Procedure Before Closing the Rear Door An example of an installation form is shown in Appendix HVisual Inspection InstallationCompletionClosing the rear door 13 Mounted TS5000 Left View Periodic Visits MaintenanceTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Packing box contains AppendixcAppendixd Tool Case Where to usePoints to Remember IntroductionInterference Bench Test for TS700 and TS800 series with JAH-L Figure E.2b Bench Test setup drawing for 10 TS modelFigure E.5 Bench test with TereScopes elevated Page Wind Force = 0.79 x Wind Speed2 x Area of Surface TS Device Momentary ExtendedFSO Chaining AppendixGUse the indoor switch in building C for the chaining SwitchFSO products & Chaining Product series No of chained links Application details Client / Dealer detailsSketch of the area Site survey Installation System failure Appendixi TS5000/155 and TS4000/155 enhancements Appendixj

TS5000/ETH/V*, TS5000/XYZ/V**, TS5000/XXX (TS5000G/XYZ/V**, TS5000/4U1/V*) specifications

MRV Communications has established a strong reputation in the networking industry, known for delivering innovative solutions that enhance the performance and reliability of communication systems. One of their standout product lines is the TS5000 series, which includes models such as TS5000/4U1/V*, TS5000/XXX, TS5000G/XYZ/V**, TS5000/XYZ/V**, and TS5000/ETH/V*. These devices are engineered to meet the growing demands of modern networks, providing a range of features that cater to various connectivity needs.

The TS5000 series is designed with versatility in mind, accommodating multiple deployment scenarios in both enterprise and service provider environments. One of the key features of the TS5000 models is their comprehensive support for multi-service operations. This means they can seamlessly handle different types of traffic including voice, video, and data, making them ideal for organizations that require robust communication solutions.

Incorporating state-of-the-art technologies, the TS5000 series supports various networking protocols and standards. This interoperability ensures compatibility with a wide array of existing network setups, allowing for easier integration and reduced overhead costs. The series utilizes advanced Ethernet technologies that enhance bandwidth efficiency and support high-speed data transfers.

Reliability is another hallmark of the TS5000 series. These devices are built with redundancy in mind, featuring hot-swappable components and failover capabilities that minimize downtime. This is critical for organizations that cannot afford interruptions in service, such as those in the finance or healthcare sectors.

Security is also a priority in the design of the TS5000 series. With built-in encryption and secure access controls, these devices help organizations protect sensitive data from cyber threats. The management interface is designed for ease of use, allowing IT teams to monitor and configure the system effortlessly.

Another notable characteristic of the TS5000 series is its scalability. Organizations can start with a basic configuration and expand their network capabilities as their needs grow. This flexibility makes the TS5000 an ideal choice for businesses aiming for future growth.

In summary, the MRV Communications TS5000 series represents a comprehensive solution for today's networking challenges. With its focus on multi-service support, advanced technology, reliability, security, and scalability, the TS5000 models are well-equipped to serve the demands of diverse environments, making them a valuable addition to any network infrastructure.