MRV Communications TS5000/XXX (TS5000G/XYZ/V, TS5000/XYZ/V, TS5000/ETH/V* IR link

Page 47

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Configuration 4: (Applicable to models G, G-F, 155, 155-F, and ETH)

Whole configuration operating test (Ping test or File transfer) for Ethernet or Fast Ethernet systems

Peripheral

Equipment

TX RX

Workstation

TX

RX

UWINTS

IR link

TSUWIN

Peripheral

Equipment

RX TX

Workstation

TX

RX

	Configuration 5: (Applicable to all models)
Whole configuration
Whole configuration		Peripheral/
operating test for all		Testing
models		Equipment
		STP		IR link
		cable		IR link
		cable

Peripheral/

Testing

Equipment

STP cable

TereScope

TereScope

36

Image 47

Contents InstallationManual Installation Manual Table of Contents Page Digital Readout vs. Distance Product specificationsTereScope Bench Test Procedure Power Supply ReplacementCE Mark StandardsStandards Compliance FCC NoticeTrademarks MRV Laser Safety CertificationOther Standards DisclaimerAboutthisInstallationManual Line Power Power Cord SafetyRequirementsBefore Installing When InstallingServicing Introduction Carefully Read the Entire Manual Before InstallingModels Part Number Description TheProductModels TS5000/M3C/V1S Using the Part Number for OrderingGeneral Description FrontBack TS5000/G Standard Model w/o Fusion and with one power supply Back Panel Description Selectors Indicators For more details please see pages 15 TS5000/155 w/o Fusion and with one power supply Power Power Supply Figures 1.5and Indicators TS5000/155-FStandard Model including Fusion option RF = 2-10 Mbps Or 100Mbps Fusion Operation ModeRF Transceiver IR = 100 Mbps or 1.25Gbps7b TS & Fusion FusionTS5000/ETH Model Back Panel TS5000/ETH Ethernet SystemSelectors DIP TS5000-4U1 Model Back Panel TS5000/4U1 4E1 or 4T1 SystemTo D Dip switch settingHeating Loop and Remote Loop Operation ModeWhen turning off the Master, the Slave exits Loop state RSM Monitoring and Management optionsManagement Dry contactCopper Connection Typical ConnectionFiber Connection Location & Range SiteSurveyLine of Sight OrientationPrefer Avoid Pay attention to Acceptable Mounting Unacceptable Mounting Mounting Environment & StabilityWall Mounting using JMP and JMB Transmitting through a Window 10 Extended Wall Mounting using JMP and MO62CInfrastructure PowerData/Signal Cabling Handle the Fibers Very Carefully Compatibility Testing equipmentSetup BenchTest TS5000/155&TS5000/155-F TS5000/4U1 Dip-switch SetupBench test Test ConfigurationsIR link Display and Results IndicatorsReceived power Optical PowerAIR RX 1000 Snmp Management Setting and Operation100 Description InstallationAccessories Do not touch this screw K Alignment Knobs Installer Tool Kit JITK-8Mounting Accessories11b Locking the screws between TS and alignment device Do not open Screws GMounting on the floor Particular Figure Cases/TechniquesPowering on the TereScope AimingProcedureScrews D & L are closed Transceiver Alignment− Coarse Alignment − Fine Alignment Swing BaseBeam cross section at the shot distance ClosedJ-R-3 Procedure Before Closing the Rear Door An example of an installation form is shown in Appendix HClosing the rear door InstallationCompletionVisual Inspection 13 Mounted TS5000 Left View Periodic Visits MaintenanceTS5000/G TS5000/155 and TS5000/155-F TS5000/ETH TS5000/4U1 4E1 or 4T1 Appendixb Packing box contains AppendixcAppendixd Tool Case Where to usePoints to Remember IntroductionInterference Bench Test for TS700 and TS800 series with JAH-L Figure E.2b Bench Test setup drawing for 10 TS modelFigure E.5 Bench test with TereScopes elevated Page Wind Force = 0.79 x Wind Speed2 x Area of Surface TS Device Momentary ExtendedFSO Chaining AppendixGUse the indoor switch in building C for the chaining SwitchFSO products & Chaining Product series No of chained links Sketch of the area Client / Dealer detailsApplication details Site survey Installation System failure Appendixi TS5000/155 and TS4000/155 enhancements Appendixj