Multi-Tech Systems RAS96 manual Humidity range 20-90% noncondensing

Page 10

RAS96 RASCard User Guide

•Humidity range: 20–90% (noncondensing).

•Power consumption: 4.5 A @ +5 VDC.

•Limited warranty: Two years.

4	CommPlete Communications Server

Image 10

Contents RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Important Safety Instructions IiiTable of Contents Solving Problems Appendix C Post CodesPage Introduction Introduction Manual OrganizationAppendix C Post Codes Technical SpecificationsAppendix B Post Messages Appendix D Approved MemoryHumidity range 20-90% noncondensing RASCard Description Memory Banks RAS96 RASCardJumpers J17 Watchdog TimerJ14, J15, J16, J18 CPU Frequency Selection Internal Connectors J22 E1 Alarm External ConnectorsJ2 Power Connector J35 VideoEthernet Status LEDs LED IndicatorsFront Panel E1 Status LEDsPower Switch SwitchesReset Switch Page Installation Pre-Installation Notes Safety WarningsInstallation Procedure Installation Page Bios Setup Utility Starting Setup Case of Problems Using SetupGetting Help Chipset Features Setup Standard Cmos SetupBios Features Setup Power Management SetupPassword Setting PCI Configuration SetupLoad Bios Defaults Load Setup Defaults IDE HDD Auto DetectionSave and Exit Setup Exit Without SavingTime Standard Cmos SetupDate Hard DisksVideo Drive a Type / Drive B TypeCGA Halt On MemoryDisabled Bios Features SetupEnabled Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence Boot Up NumLock StatusMemory Parity Check Typematic Rate SettingGate A20 Option Typematic Rate Chars/SecSecurity Option Typematic Delay MsecVideo Bios Shadow C8000 Cffff Shadow/DC000 Dffff ShadowSystem Bios Cacheable Chipset Features SetupDram Timing IDE HDD Block Mode Video Bios CacheableBit I/O Recovery Time Memory Hole At 15M-16MPCI Streaming On-Chip Primary PCI IDEPCI Concurrancy PCI BurstingPower Management Setup Power ManagementSuspend Mode Doze ModeStandby Mode HDD Power DownLPT Ports Accessed Power Down ActivitiesCOM Ports Accessed Drive Ports AccessedSlot x Using INT# PCI Configuration Setup1st/2nd/3rd/4th Available IRQ PCI IRQ Activated by PCI IDE IRQ Map toPassword Setting Enter PasswordPage E1 Daughter Cards Specifications E1 OverviewE1 Glossary E1 Basics E1 Line Coding Signaling OptionsE1 Frame Formats Dnis digitsCountry Selection Pin Signal E1 Facility TerminationE1 Line Monitoring Jack RJ-11 Alarm JackPCB Description Test ModesChannelized E1 line with 30 DS-0 channels E1 Frame Format Configuration of the E1 Daughter CardOrdering an E1 Line Line CodingTo Configure the E1 Daughter Card Factory DefaultsE1 Commands Command ExampleRAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Command Messages E1 Status LEDsFunctional Description Solving Problems Troubleshooting RASCard has no videoCOM1 port does not respond correctly Invalid time, date or setupKeyboard does not respond to key strokes Memory Upgrade Diagnostic Tests Calling Technical SupportRAS96 RASCard User Guide Appendixes Keyboard Connector J11 Appendix a Connector PinoutsVideo Connector J35 COM1 Connector J3 E1 Alarm Connector J22Pin Floppy Disk Drive Connector J27 Drive Power Connector J13Hard Disk Connector J6 IOCS16IDE Connector J21 Figure A-7. IDE connectorAppendix B Post Messages Error MessagesPost Beep Memory parity Error at Memory Address Error atMemory Verify Error at Offending Segment Appendix C Post Codes Code Name DescriptionPost Codes E1-EF Appendix D Approved Memory Capacity Speed Type Manufacturer Part Number Usable MBEMC, Safety and Terminal Directive Compliance Appendix E Regulatory Information