Multi-Tech Systems RAS96 manual COM1 Connector J3, E1 Alarm Connector J22

Page 71

A Connector Pinouts

COM1 Connector (J3)

This serial port connector can be used to configure the RASCard or to connect a mouse to the RASCard.

Figure A-3. DB-9 COM1 connector.

Pin Description	Pin Description

DCD	DSR
RX Data	RTS
TX Data	CTS
DTR	RI
Ground

E1 Alarm Connector (J22)

Figure A-5. E1 alarm connector.

	Pin	Description	Notes

	1	Close 2	Alarm signals for
	2	Open 2	second E1 card
	2	Open 2	(future upgrade)
			(future upgrade)
	3	Common 2

	4	Close 1	Alarm signals for
	5	Open 1	first E1 card
	5	Open 1	(default)
			(default)
	6	Common 1

CommPlete Communications Server

63

Image 71

Contents RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Iii Important Safety InstructionsTable of Contents Appendix C Post Codes Solving ProblemsPage Introduction Manual Organization IntroductionAppendix D Approved Memory Technical SpecificationsAppendix B Post Messages Appendix C Post CodesHumidity range 20-90% noncondensing RASCard Description RAS96 RASCard Memory BanksJ14, J15, J16, J18 CPU Frequency Selection J17 Watchdog TimerJumpers Internal Connectors J35 Video External ConnectorsJ2 Power Connector J22 E1 AlarmE1 Status LEDs LED IndicatorsFront Panel Ethernet Status LEDsReset Switch SwitchesPower Switch Page Installation Installation Procedure Safety WarningsPre-Installation Notes Installation Page Bios Setup Utility Starting Setup Getting Help Using SetupCase of Problems Power Management Setup Standard Cmos SetupBios Features Setup Chipset Features SetupLoad Bios Defaults PCI Configuration SetupPassword Setting IDE HDD Auto Detection Load Setup DefaultsExit Without Saving Save and Exit SetupHard Disks Standard Cmos SetupDate TimeCGA Drive a Type / Drive B TypeVideo Memory Halt OnVirus Warning Bios Features SetupEnabled DisabledBoot Up NumLock Status Quick Power On Self TestBoot Sequence Boot Up Floppy SeekTypematic Rate Chars/Sec Typematic Rate SettingGate A20 Option Memory Parity CheckC8000 Cffff Shadow/DC000 Dffff Shadow Typematic Delay MsecVideo Bios Shadow Security OptionDram Timing Chipset Features SetupSystem Bios Cacheable Memory Hole At 15M-16M Video Bios CacheableBit I/O Recovery Time IDE HDD Block ModePCI Bursting On-Chip Primary PCI IDEPCI Concurrancy PCI StreamingPower Management Power Management SetupHDD Power Down Doze ModeStandby Mode Suspend ModeDrive Ports Accessed Power Down ActivitiesCOM Ports Accessed LPT Ports Accessed1st/2nd/3rd/4th Available IRQ PCI Configuration SetupSlot x Using INT# PCI IDE IRQ Map to PCI IRQ Activated byEnter Password Password SettingPage E1 Daughter Cards E1 Overview SpecificationsE1 Glossary E1 Basics Dnis digits Signaling OptionsE1 Frame Formats E1 Line CodingCountry Selection E1 Facility Termination Pin SignalTest Modes RJ-11 Alarm JackPCB Description E1 Line Monitoring JackLine Coding Configuration of the E1 Daughter CardOrdering an E1 Line Channelized E1 line with 30 DS-0 channels E1 Frame FormatFactory Defaults To Configure the E1 Daughter CardCommand Example E1 CommandsRAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Status LEDs E1 Command MessagesFunctional Description Solving Problems RASCard has no video TroubleshootingKeyboard does not respond to key strokes Invalid time, date or setupCOM1 port does not respond correctly Memory Upgrade Calling Technical Support Diagnostic TestsRAS96 RASCard User Guide Appendixes Video Connector J35 Appendix a Connector PinoutsKeyboard Connector J11 E1 Alarm Connector J22 COM1 Connector J3Drive Power Connector J13 Pin Floppy Disk Drive Connector J27IOCS16 Hard Disk Connector J6Figure A-7. IDE connector IDE Connector J21Post Beep Error MessagesAppendix B Post Messages Memory Verify Error at Memory Address Error atMemory parity Error at Offending Segment Code Name Description Appendix C Post CodesPost Codes E1-EF Capacity Speed Type Manufacturer Part Number Usable MB Appendix D Approved MemoryAppendix E Regulatory Information EMC, Safety and Terminal Directive Compliance