Multi-Tech Systems RAS96 manual Gate A20 Option, Memory Parity Check, Typematic Rate Setting

Page 35

4 BIOS Setup Utility

Gate A20 Option

This entry allows you to select how the gate A20 is handled. The gate A20 is a device used to address memory above 1 MB. Initially, the gate A20 was handled via a pin on the keyboard. Today, though keyboards still provide this support, it is more common, and much faster, for the system chipset to provide support for gate A20.

Normal Keyboard.

Fast

Chipset (Default).

Memory Parity Check

Parity is a method of checking for errors in system memory. There are both parity and non-parity memory types. At boot, the Award BIOS both sizes and tests all memory. Normally, when a parity error is detected, the BIOS will display a message describing the problem as well as the problem’s location, if possible. The boot process will then terminate and you will not be able to continue until the bad SIMM is located and replaced.

Disabling the Memory Parity Check allows the system to bypass the test and allow your system to boot. You then have a choice of continuing to operate your system or attempting to remedy the problem.

Enabled

Normal memory parity check (Default).

Disabled

Ignore memory parity check.

Typematic Rate Setting

This determines if the typematic rate is to be used. When it is disabled, continually holding down a key on your keyboard will generate only one character. In other words, the BIOS will only report that the key is down. When the typematic rate is enabled, the BIOS will report as before, but it will then wait a moment and, if the key is still down, it will begin to report that the key has been depressed repeatedly. For example, you would use such a feature to accelerate cursor movements with the arrow keys.

Enabled

Enable typematic rate.

Disabled

Disable typematic rate (Default).

Typematic Rate (Chars/Sec)

When the typematic rate is enabled, this item allows you select the rate at which the system registers repeated keystrokes.

6

6 characters per second.

8

8 characters per second.

10

10 characters per second.

12

12 characters per second.

15

15 characters per second.

20

20 characters per second.

24

24 characters per second.

30

30 characters per second.

CommPlete Communications Server

29

Image 35
Contents RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Iii Important Safety InstructionsTable of Contents Appendix C Post Codes Solving ProblemsPage Introduction Manual Organization IntroductionAppendix D Approved Memory Technical SpecificationsAppendix B Post Messages Appendix C Post CodesHumidity range 20-90% noncondensing RASCard Description RAS96 RASCard Memory BanksJ14, J15, J16, J18 CPU Frequency Selection J17 Watchdog TimerJumpers Internal Connectors J35 Video External ConnectorsJ2 Power Connector J22 E1 AlarmE1 Status LEDs LED IndicatorsFront Panel Ethernet Status LEDsReset Switch SwitchesPower Switch Page Installation Installation Procedure Safety WarningsPre-Installation Notes Installation Page Bios Setup Utility Starting Setup Getting Help Using SetupCase of Problems Power Management Setup Standard Cmos SetupBios Features Setup Chipset Features SetupLoad Bios Defaults PCI Configuration SetupPassword Setting IDE HDD Auto Detection Load Setup DefaultsExit Without Saving Save and Exit SetupHard Disks Standard Cmos SetupDate TimeCGA Drive a Type / Drive B TypeVideo Memory Halt OnVirus Warning Bios Features SetupEnabled DisabledBoot Up NumLock Status Quick Power On Self TestBoot Sequence Boot Up Floppy SeekTypematic Rate Chars/Sec Typematic Rate SettingGate A20 Option Memory Parity CheckC8000 Cffff Shadow/DC000 Dffff Shadow Typematic Delay MsecVideo Bios Shadow Security OptionDram Timing Chipset Features SetupSystem Bios Cacheable Memory Hole At 15M-16M Video Bios CacheableBit I/O Recovery Time IDE HDD Block ModePCI Bursting On-Chip Primary PCI IDEPCI Concurrancy PCI StreamingPower Management Power Management SetupHDD Power Down Doze ModeStandby Mode Suspend ModeDrive Ports Accessed Power Down ActivitiesCOM Ports Accessed LPT Ports Accessed1st/2nd/3rd/4th Available IRQ PCI Configuration SetupSlot x Using INT# PCI IDE IRQ Map to PCI IRQ Activated byEnter Password Password SettingPage E1 Daughter Cards E1 Overview SpecificationsE1 Glossary E1 Basics Dnis digits Signaling OptionsE1 Frame Formats E1 Line CodingCountry Selection E1 Facility Termination Pin SignalTest Modes RJ-11 Alarm JackPCB Description E1 Line Monitoring JackLine Coding Configuration of the E1 Daughter CardOrdering an E1 Line Channelized E1 line with 30 DS-0 channels E1 Frame FormatFactory Defaults To Configure the E1 Daughter CardCommand Example E1 CommandsRAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Status LEDs E1 Command MessagesFunctional Description Solving Problems RASCard has no video TroubleshootingKeyboard does not respond to key strokes Invalid time, date or setupCOM1 port does not respond correctly Memory Upgrade Calling Technical Support Diagnostic TestsRAS96 RASCard User Guide Appendixes Video Connector J35 Appendix a Connector PinoutsKeyboard Connector J11 E1 Alarm Connector J22 COM1 Connector J3Drive Power Connector J13 Pin Floppy Disk Drive Connector J27IOCS16 Hard Disk Connector J6Figure A-7. IDE connector IDE Connector J21Post Beep Error MessagesAppendix B Post Messages Memory Verify Error at Memory Address Error atMemory parity Error at Offending Segment Code Name Description Appendix C Post CodesPost Codes E1-EF Capacity Speed Type Manufacturer Part Number Usable MB Appendix D Approved MemoryAppendix E Regulatory Information EMC, Safety and Terminal Directive Compliance